Mitsubishi HS-1096E, Installation And Operation Manual

Page: 11 / 32

11
Advanced Functions
Reference page
ENGLISH
Example : Setting the program number 2 to the L18H mode
timer recording from 12:00 to 15:00 every Tuesday.
1. Press MENU button.
• <MAIN MENU> appears.
2. Turn JOG to select TIMER PROGRAM
and turn SHUTTLE to the right.
• <TIMER PROGRAM> menu appears.
3. When the cursor ( ) is next to
PROGRAM TO RECORD, turn
SHUTTLE to the right.
• <PROGRAM TO RECORD> menu
appears.
4. Turn JOG to select the program number
and turn SHUTTLE to the right to select.
5. In the DW column, turn JOG to select
the Day of the Week. Turn SHUTTLE
to the right to select.
6. In the START column, turn JOG to
select the hour digits of the start time.
Turn SHUTTLE to the right when done.
Set the 10-minutes digit and 1-
minute digit in a similar fashion.
7. In the END column, turn JOG to select
the hour digits of the end time. Turn
SHUTTLE to the right when done.
Set the 10-minute digit and 1-
minute digit in a similar fashion.
8. In the HR column, turn JOG to select
the RECORDING mode.
Setup step 9 to make recording while the REC IN terminal is
grounded. If not, go to step 10.
9. Press MENU button.
• The program you are currently setting is highlighted.
• Press MENU button again to cancel.
Recording Techniques
<PROGRAM TO RECORD>
DW START END HR
1 --- --:-- --:-- ------
2 --- --:-- --:-- ------
3 --- --:-- --:-- ------
4 --- --:-- --:-- ------
5 --- --:-- --:-- ------
6 --- --:-- --:-- ------
7 --- --:-- --:-- ------
8 --- --:-- --:-- ------
1 6 5 4 3 2
1) Program number
Up to 8 programs can be set.
2) Day of the week display
• Display HLD to apply HOLIDAY SET UP setting ( see below).
• Display SPL to apply SPECIAL DW setting ( next page).
• Display DAY to record at the programmed time everyday.
3) Recording start-time
4) Next day indicator (•)
Recording continues to the following day.
5) Recording end-time
6) Recording mode
• Recording mode varies by the TAPE LENGTH setting of FIRST TIME
SET UP menu. See the table shown to the left.
• Timer recording will not be performed when set to SKIP.
Info.
• Time is displayed in 24-hour format.
Accurately preset the day and present time before timer programming. ( page 9 or 21)
Timer Recording
<MAIN MENU>
DISPLAY
TIMER PROGRAM
RECORDING SET UP
REAR TERMINAL
MAINTENANCE
CLOCK/FIRST TIME SET UP
<TIMER PROGRAM>
PROGRAM TO RECORD
HOLIDAY SET UP
SPECIAL DW MON-SAT
<PROGRAM TO RECORD>
DW START END HR
1 DAY 08:00 20:00 L30LP
2 --- --:-- --:-- ------
3 --- --:-- --:-- ------
<PROGRAM TO RECORD>
DW START END HR
1 DAY 08:00 20:00 L30LP
2 --- --:-- --:-- ------
3 --- --:-- --:-- ------
<PROGRAM TO RECORD>
DW START END HR
1 DAY 08:00 20:00 L30LP
2 TUE --:-- --:-- ------
3 --- --:-- --:-- ------
<PROGRAM TO RECORD>
DW START END HR
1 DAY 08:00 20:00 L30LP
2 TUE 12:00 --:-- ------
3 --- --:-- --:-- ------
<PROGRAM TO RECORD>
DW START END HR
1 DAY 08:00 20:00 L30LP
2 TUE 12:00 15:00 ------
3 --- --:-- --:-- ------
<PROGRAM TO RECORD>
DW START END HR
1 DAY 08:00 20:00 L30LP
2 TUE 12:00 15:00 L18LP
3 --- --:-- --:-- ------
<PROGRAM TO RECORD>
DW START END HR
1 DAY 08:00 20:00 L30LP
2 TUE 12:00 15:00 L18LP
3 --- --:-- --:-- ------
10. Turn SHUTTLE to the right when
done. (Cursor flashing will stop.)
• If the program has not been set
completely, the DW column will
continue to flash.
Repeat steps 4 to 10 to set 2 or more programs at once.
11. Press MENU button.
• The day and present time display appears on screen.
12. Press TIMER REC button.
• The VCR is turned off and the Timer Recording indicator
( ) illuminates on the fluorescent display.
When TIMER REC button is pressed during the
programmed period, the VCR starts recording immediately.
Info.
When the Timer Recording indicator ( ) starts flashing:
a) A tape is not inserted.
b) A tape without erase prevention tab is inserted.
c) Day and present time has not been set.
d) Timer program has not been set.
e) Menu item has been set (flashing).
– Remedy -
1. Press TIMER REC button to turn off the Timer Recording
indicator ( ).
2. a) Insert a tape.
b) Insert a tape with erase prevention tab intact.
c) Set the day and present time. (
page 9 or 21)
d) Confirm the program.
e) Turn SHUTTLE to the right to stop flashing.
3. Press TIMER REC button to turn on the Timer Recording indicator.
Info.
• To erase a program:
Select the program number you wish to erase, turn SHUTTLE to
the right (DW column flashes) and then turn SHUTTLE to the left.
Holiday set up
Up to 20 days per year can be set for days for when the timer
recording will be performed, or if HR in PROGRAM TO
RECORD menu is set to SKIP, the timer recording will not be
performed during the programmed period.
1. Display <TIMER PROGRAM> menu.
2. Turn JOG to select HOLIDAY SET UP
and turn SHUTTLE to the right.
• <HOLIDAY SET UP> menu appears.
3. Turn JOG to move the cursor ( ) and
turn SHUTTLE to the right.
• Each time JOG is turned to the right, the cursor moves
towards right-forward direction.
<HOLIDAY SET UP>
01/01 15/01 11/02 22/03
29/04 03/05 04/05 05/05
20/07 15/09 23/09 10/10
03/11 23/11 23/12 - - / - -
- - / - - - - / - - - - / - - - - / - -
DAY/MONTH
E-180
E-240
4SP 8LP L24LP L40LP
64LP 96LP 128LP SKIP
3SP 6LP L18LP L30LP
48LP 72LP 96LP SKIP