Mitsubishi FR - S500 Instruction Manual Download Page 89

Page: 89 / 196

Explanation of functions (parameters)

UNCT

2.3.14 Acceleration/deceleration pattern (Pr. 29

)

<Setting>

Set the acceleration/deceleration pattern.

Parameter

Name

Factory

Setting

Range

Remarks

Acceleration/
deceleration pattern

0, 1, 2

Setting is enabled when Pr. 30 = "1".

Pr. 29

Setting

Function

Description

Linear
acceleration/
deceleration

Acceleration is made to the set frequency linearly.

(Factory setting)

S-pattern
acceleration/
deceleration A (*)

For machine tool spindle applications, etc.

Used when acceleration/deceleration must be made in a short

time to a high-speed region of not lower than the base

frequency. Acceleration/deceleration is made in a pattern

where fb (base frequency) acts as the inflection point of an S

shape, and you can set the acceleration/deceleration time

which matches the motor torque reduction in the constant-

output operation region of not lower than the base frequency.

S-pattern
acceleration/
deceleration B

For prevention of load shifting in conveyor and other

applications. Since acceleration/deceleration is always made in

an S shape from f2 (current frequency) to f1 (target frequency),

this function eases shock produced at acceleration/

deceleration and is effective for load collapse prevention, etc.

CAUTION

* As the acceleration/deceleration time, set the time taken to reach the Pr. 3

"base frequency" value, not the Pr. 20 "acceleration/deceleration reference

frequency" value.

♦

Related parameters

♦

•

Base frequency (acceleration/deceleration time setting) setting

⇒

Pr. 3 "base frequency"

(refer to page 65)

•

Pr. 20 "acceleration / deceleration reference frequency"

⇒

refer to page 67

•

For setting of "1" (S-pattern acceleration/deceleration A)

⇒

Pr. 44 "second acceleration/deceleration time", Pr. 45 "second deceleration time" (refer to

page 67)

uenc

y (

Time

[S-pattern
acceleration/deceleration A]

Set value 1

ncy (

[S-pattern
acceleration/deceleration B]

Set value 2

Time

Set value 0

Time

ncy (

[Linear
acceleration/deceleration]

Summary of Contents for FR - S500





































































































































































































Search results

Summary of Contents for FR - S500

Reviews:

Brands by name

Popular brands

Mitsubishi FR - S500, Instruction Manual

Search results

Summary of Contents for FR - S500

Reviews:

Brands by name

Popular brands