Mitsubishi ECLIPSE CROSS 2017 Owner'S Manual Download Page 190 | Manualshive

Page: 190 / 538

background image

Changing the operation mode

E00631901298

If you press the engine switch without de-
pressing the brake pedal (CVT) or the clutch
pedal (M/T), you can change the operation
mode in the order of OFF, ACC, ON, OFF.

CAUTION

l

When the engine is not running, put the op-
eration mode in OFF. Leaving the operation
mode in ON or ACC for a long time when
the engine is not running may cause the bat-
tery to be discharged, making it impossible
to start the engine, lock and unlock the steer-
ing wheel.

CAUTION

l

When  the  battery  is  disconnected,  the  cur-
rent operation mode is memorized. After re-
connecting the battery, the memorized mode
is selected automatically. Before disconnect-
ing  the  battery  for  repair  or  replacement,
make sure to put the operation mode in OFF.
Be  careful  if  you  are  not  sure  which  opera-
tion mode the vehicle is in when the battery
is run down.

l

The operation mode cannot be changed from
OFF to ACC or ON if the keyless operation
key is not detected to be in the vehicle. Refer
to “Keyless operation system: operating
range for starting the engine ” on page 3-11.

l

When there is the keyless operation key in
the vehicle and the operation mode is not
changed, the battery in the keyless operation
key may have worn out. Refer to “Warning
activation” on page 3-14.

NOTE

l

If the operation mode cannot be changed to
OFF, perform the following procedure.

1

.

Move the selector lever to the “P”
(PARK) position, and then change
the operation mode to OFF. (For ve-
hicles with CVT)

NOTE

2

.

One of the other causes could be low
battery  voltage.  If  this  occurs,  the
keyless  entry  system,  keyless  opera-
tion  function  and  steering  lock  will
also

not

operate.

Contact

a

MITSUBISHI MOTORS Authorized
Service Point.

ACC power auto-cutout func-

tion

E00632801311

After approximately 30 minutes have elapsed
with  the  operation  mode  in  ACC,  the  func-
tion automatically cuts out the power for the
audio  system  and  other  electric  devices  that
can be operated with that position.
When  the  engine  switch  operate  again,  the
power is supplied again.

NOTE

l

It is possible to modify functions as follows:

•

The time until the power cuts out can be
changed to approximately 60 minutes.

Engine switch*

6-16

OGKE18E1

Starting and driving

6

«
...
188
189
190
191
192
...
»

Summary of Contents for ECLIPSE CROSS 2017



























































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for ECLIPSE CROSS 2017

Brand: AAMP of America Pages: 6

Brand: Jeep Pages: 25

Brand: Jeep Pages: 51

Brand: Farenheit Pages: 8

Brand: Jeep Pages: 603

Brand: Jeep Pages: 80

NPL-TV 7874 DIGITAL

Brand: Napoli Pages: 20

Brand: FormFit Pages: 4

Brand: Audi Pages: 12

Carpower CAP-20

Brand: Monacor Pages: 2

Brand: ConWys AG Pages: 16

Brand: rough country Pages: 4

Hatch-bag Luggage System

Brand: Tabernus Peram Pages: 10

Brand: Prorack Pages: 15

Brand: v.link Pages: 19

Brand: Axxess Pages: 8

Brand: PEUGEOT Pages: 404

PRIME DESIGN UXV 211

Brand: Safe Fleet Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands