Mitsubishi AJ65S-64AD-U-H-JE User Manual Download Page 7

 

1

 

 1. Overview 

 

 
This user's manual explains the specifications, names and setting of parts, wiring 
and others of Type AJ65SBT-64AD analog-digital converter module (hereafter 
abbreviated to the “AJ65SBT-64AD”) which is used as a remote device station of 
a CC-Link system. 
 

 2. Specification 

 

 

2.1 General specifications 

The general specifications of the AJ65SBT-64AD are shown below. 

 

Item Specification 

Usage ambient 
temperature 

0 to 55°C 

Storage ambient 
temperature 

-20 to 75°C 

Usage ambient 
humidity 

10 to 90%RH, no condensation 

Storage ambient 
humidity 

10 to 90%RH, no condensation 

When there is intermittent vibration 

Frequency Acceleration Amplitude Sweep 

count 

10 to 57Hz 

— 

0.075mm 

(0.0030inch) 

57 to 150Hz 

9.8m/s

2

 

— 

10 times in 

each direction 

X, Y, Z 

When there is continuous vibration 

Frequency Acceleration Amplitude Sweep 

count 

10 to 57Hz 

— 

0.035mm 

(0.0014inch) 

Vibration durability 

Conforming to 

JIS B 3502, 

IEC 61131-2 

57 to 150Hz 

4.9m/s

2

 

— 

— 

Shock durability 

Conforming to JIS B 3502, IEC 61131-2  

(147m/s

2

, 3 times each in 3 directions) 

Usage environment 

No corrosive gas 

Usage height *

3

 

Less than 2000m (less than 6562ft.) 

Installation area 

Within the control board 

Over-voltage 
category *

1

 

Less than II 

Pollution level *

2

 

Less than 2 

*1 Indicates the location where the device is connected from the public cable network to the 

device structure wiring area. 
Category II applies to the devices to which the power is supplied from a fixed equipment. 
Surge withstand voltage for devices with up to 300V of rated voltage is 2500V. 

*2 This is an index which indicates the degree of conductive object generation in the 

environment Pollution level 2 is when only non-conductive pollution occurs.  
A temporary conductivity caused by condensation must be expected occasionally. 

*3 Do not operate or store the programmable controller in the environment where the pressure 

applied is equal to greater than the atmospheric pressure at the altitude of 0m. 
Doing so may cause a malfunction. Please consult our branch office when the 
programmable controller is to be operated under pressure. 
 

 

Summary of Contents for AJ65S-64AD-U-H-JE

















Reviews: