manualshive.com logo in svg

Mitsubishi A1SH, User Manual, Page: 80 / 186

Share
Download
Mitsubishi A1SH User Manual Download Page 80

7. MEMORY CASSETTE AND BATTERY

7 - 3

MELSEC-A

7.1.3

Installing and removing a memory cassette

!

 DANGER

•

  Push the memory cassette onto the fixing connector to install it securely. Check that floating

does not occur after its installation.
Poor contact could result in a malfunction.

The installation/removal method of the memory cassette is common in all
AnSHCPU models, but the installation position is unique to each model.

Memory cassette installation position: A1SHCPU/A2SHCPU(-S1) ----- Left side

A1SJHCPU(S8) --- Front

(1)

Installing a memory cassette

Hook

A1SHCPU

A1SHCPU

A1SNMCA

-8KE

Hook

Hook catch

Hook

Hook

Hook

A1SJHCPU

A1SJHCPU

Hook

Hook catch

Memory cassette

(a)

Hold the memory cassette vertically so that its model name is right side
up and its connector faces the AnSHCPU module.  Insert the memory
cassette all the way in the AnSHCPU module so that the hooks of the
memory cassette are completely engaged (they will click).

(b)

Make sure the hooks are completely engaged.

Summary of Contents for A1SH



























































































































































































Reviews:

No comments