EN-69
Troubleshooting
Before asking for repair of the projector, check the following. If the symptom persists, stop using the projector, be
sure to unplug the power plug, and then contact your dealer.
No image appears on the screen.
Problem
Solution
Power can not be
turned on.
t $IFDLXIFUIFSUIFJOEJDBUPSTBSFPOPSPGGBOEIPXUIFZBSFMJHIUOJOH
POWER LAMP 1 LAMP 2 STATUS FILTER
Solution
Off
Off
Off
Off
Off
t $POOFDUUIFQPXFSDPSEUPUIFQSPKFDUPS
t 1MVHUIFQPXFSDPSEJOUPBXBMMPVUMFU
Steady red
Off
Off
Off
Off
t *GBOZPCKFDUTBSFCMPDLJOHUIFJOUBLFPSFYIBVTU
vents, remove them and carry out the following.
Unplug the power cord from the wall outlet.
1.
Make sure that the projector has cooled off.
2.
Plug the power cord into a wall outlet.
3.
Press the POWER button.
4.
Off
Off
Blinking
orange
Off
t *GBOZPCKFDUTBSFCMPDLJOHUIFJOUBLFPSFYIBVTU
vents, remove them.
t %POUFYQPTFUIFFYIBVTUWFOUTUPIPUBJSFNJUUFE
from a heating appliance.
t $IFDLXIFUIFSUIFmMUFSJTEJSUZPSOPU
→
Clean the filter. (See page 67.)
Blinking green*
Off
Off
t 8BJUVOUJMUIF-".1JOEJDBUPSTTUPQCMJOLJOHHSFFO
and then press the POWER button.
t *GZPVVOQMVHUIFQPXFSDPSEXIJMFUIFGBOJTSPUBUJOHUIF
lamp may not turn on about 2 minutes when you plug the
power cord next time.
t
The lamp can’t turn on again for 2 minutes after it goes out.
t 1SFTTUIF108&3CVUUPOTFWFSBMUJNFT
Steady red*
Off
Off
t 3FQMBDFUIFMJHIUTPVSDFMBNQJOEJDBUFECZUIF
illuminating indicator. (The time for replacing the light
source lamp has come.)
Blinking
red/green
Off
Off
Off
Off
t "UUBDIUIFMBNQDPWFSBOEmMUFSDPWFS
Steady*
or
Blinking*
t 6OQMVHUIFQPXFSDPSEGSPNUIFXBMMPVUMFUBOE
contact your dealer.
*: Status of either or both of the indicators.
No image appears on
the screen.
t 1SFTTUIF#-"/,CVUUPOUPDBODFM#-"/,
t $IFDLUIBUUIFMFOTDBQJTSFNPWFE
t *UNBZUBLFBCPVUNJOVUFTGPSUIFMBNQUPMJHIUVQ
t 5IFMBNQGBJMTUPMJHIUVQPOSBSFPDDBTJPOT*OTVDIBDBTFXBJUGPSBGFXNJOVUFT
and then try again.
t *GUIFQSPKFDUPSXBTUVSOFEPGGCFGPSFUIFMBNQXBTDPPMFEEPXOTVGmDJFOUMZMBTUUJNF
the fan may start rotating and the POWER button may not work after the power cord
is plugged. After the fan stops rotating, press the POWER button to turn back on the
POWER indicator.
t 4FU4$"35*/165JOUIF'&"563&NFOVUP0'' 4FFQBHF
t $IFDLUIBUUIFJOUBLFWFOUJTDMFBO
t $IFDLUIBUUIFDBCMFTDPOOFDUFEUPUIFFYUFSOBMEFWJDFTBSFOPUCSPLFO
t
When an extension cable is being used, replace it with the supplied cable for check.
When images are displayed correctly, add an RGB signal amplifier to the extension cable.
Power turns off.
t 5IJTQSPCMFNNBZPDDVSXIFOUIFJOUBLFWFOUBOEPSFYIBVTUWFOUTBSFCMPDLFE *O
such a case, the STATUS indicator brinks orange.)
Remove the objects blocking the intake vent and/or exhaust vents and then carry
out the following procedure.
1. Wait for the intake fan and/or exhaust fan to stop. (Wait until the STATUS indicator
goes out.)
2. Unplug the power cord from the wall outlet.
3. Wait about 10 minutes.
4. Plug the power cord into a wall outlet.
5. Press the POWER button.
t 8IFOUIF-".1JOEJDBUPSJTTUFBEZSFEJUJTJOEJDBUJOHUIBUUIFMBNQTIPVMECF
replaced. Replace the lamp that is being indicated by the indicator.
t $IFDLUIBU"650108&30''IBTCFFOTFUUP0''
t *GUIFMBNQIBTEFUFSJPSBUFEJUNBZHPPVUBGUFSBXIJMFJUJMMVNJOBUFT
