20
NOTE:
• The operation settings are memorized when 10 seconds have passed after the indoor unit was operated with the remote
controller.
• If main power is turned OFF or a power failure occurs while AUTO START/STOP timer is active, the timer setting is can-
celled.
• If the unit has been off with the remote controller before power failure, the auto restart function does not work as the
power button of the remote controller is OFF.
• To prevent breaker OFF due to the rush of starting current, systematize other home appliance not to turn ON at the same
time.
• When some air conditioners are connected to the same supply system, if they are operated before power failure, the start-
ing current of all the compressors may flow simultaneously at restart.
Therefore, the special countermeasures are required to prevent the main voltage-drop or the rush of the starting current
by adding to the system that allows the units to start one by one.
This Wi-Fi interface communicates the status information and controls the commands from the MELCloud by connecting to an indoor unit.
(1)
MODE switch
• The MODE switch is used for selecting modes in configurations.
(2)
RESET switch
• Hold down the RESET switch for 2 seconds to reboot the system.
• Hold down the RESET switch for 14 seconds to initialize the Wi-Fi interface
to the factory default.
(1) Open the front panel and remove the Wi-Fi interface.
(2) Set up a connection between the Wi-Fi interface and the router.
Refer to the SETUP MANUAL and SETUP QUICK
REFERENCE GUIDE provided with the unit.
For SETUP MANUAL, please go to the website below.
http://www.melcloud.com/Support
(3) Put the Wi-Fi interface back and close the front panel
after the setup is completed.
(4) For MELCloud User Manual, please go to the website below.
http://www.melcloud.com/Support
NOTE:
Mitsubishi Electric’s Wi-Fi interface is designed for communication to Mit-
subishi Electric’s MELCloud Wi-Fi service.
Third party Wi-Fi interfaces cannot be connected to MELCloud.
Mitsubishi Electric is not responsible for any (i) under performance of a sys-
tem or any product; (ii) system or product fault; or (iii) loss or damage to any
system or product; which is caused by or arises from connection to and/or use
of any third party Wi-Fi interface or any third party Wi-Fi service with Mitsubishi
Electric equipment.
For the latest information regarding MELCloud from Mitsubishi Electric
Corporation, please visit www.MELCloud.com.
NOTE:
When the Wi-Fi interface is reset to the factory default, ALL the
configuration information will be lost. Take great care in implementing this
operation.
No.
Item
Description
1
MODE switch
It selects modes.
2
RESET switch
It resets the system and ALL settings.
3
ERR LED (Orange)
It shows the network error state.
4
NET LED (Green)
It shows the network state.
5
MODE LED (Orange)
It shows the Access point mode state.
6
UNIT LED (Green)
It shows the indoor unit state.
Wi-Fi interface introduction
<MSZ-AP25/35/42/50VGK>
<MSZ-AP60/71VGK>
Wi-Fi interface
Wi-Fi interface
Front panel
Front panel
Wi-Fi interface
Wi-Fi interface
Front panel
Front panel
• Ensure that the Router supports the WPA2-AES encryption setting before
starting the Wi-Fi interface setup.
• The End user should read and accept the terms and conditions of the Wi-Fi
service before using this Wi-Fi interface.
• To complete connection of this Wi-Fi interface to the Wi-Fi service, the Rout-
er may be required.
• This Wi-Fi interface will not commence transmission of any operational data
from the system until the End user registers and accepts the terms and con-
ditions of the Wi-Fi service.
• This Wi-Fi interface should not be installed and connected to any Mitsubishi
Electric system which is to provide application critical cooling or heating.
• At the time of relocation or disposal, reset the Wi-Fi interface to the factory
default.
RESET
ERR
NET
MODE
UNIT
MODE
3
4
5
6
2
1
8-4. Wi-Fi INTERFACE SETTING UP (MSZ-AP∙VGK)
OBH788C
