background image

Main

2

3

1

Do not use in the following locations:

Locations where the temperature could be lower than 0˚C or higher than 40

°

C.

Locations where the humidity could be lower than 5% RH or higher than 95%RH.
Locations where the unit may come into direct contact with water.
Locations where the unit is under direct or strong sunlight. (May cause sensor to malfunction.)
Locations where there is a lot of condensation.
Do not use with chemicals (detergents, etc.) on your hands. (This may reduce the productive life of the unit.)
Do not use in locations where corrosive, neutral, or reductive gases are present.
(This may reduce the productive life of the unit and/or cause malfunctions.)
Locations where solt damage may occur.

Vehicles (incl. vessels, trains.)

Note 

Features 

Tamper-proof timer

To prevent tampering with the unit, the built-in timer shuts it down after 30 seconds of continuous use. 
To continue use, remove hands and then re-insert.

"No-touch" hand drying, ensuring complete hygiene.
The jet-blow air dries wet hands quickly. You only pay for the electricity used to run it, so it’s economical.
A tamper-proof timer is built in to prevent overuse.
No need to throw out or replace paper towels, so maintenance is a cinch.
Anti-microbial finish.

As the jet-blow air is warmed with the heater, it will not feel cold even 
when using in winter. (The unit accumulates heat because the heater 
operates while the hand dryer is not used.)
Hot blow air dries hands quickly.

Although the heater is turned on when the heater switch is turned “ON”, the power is turned off automatically when the 
room temperature becomes higher than 35˚C (temperatures at around the hand dryer).
When the heater switch is turned “ON”, the electricity is consumed because the heater operates while the hand dryer 
is not used.
The heater is turned off automatically when using the hand dryer. (Motor and heater will not turn on simultaneously.)

Safety precautions

 (Continued)

 

2

Features of the heater

Hot jet-blow air …

Note

JT-SB116EH-W-CA-IB_874HD6901-GB    06.12.9  2:12  PM    ページ 3

Summary of Contents for T-SB116EH-W-CA









Reviews: