Mitsubishi Electric PUHZ-RP100VHA3 Service Manual Download Page 133

Page: 133 / 186

133

OPERATING PROCEDURE

PHOTOS

4. Removing the thermistor <Outdoor 2-phase pipe> (TH6)
and thermistor <Outdoor pipe> (TH3) (TH33)

(1) Remove the service panel. (See Photo 2.)

(2) Remove the top panel. (See Photo 1)

(3) Remove the front panel. (See Photo 1)

(4) Remove the back panel fixing screws, 4 from the right and

3 from the rear side, and detach the back panel.

(See photo 1.)

(5) Disconnect the connector TH3 (white) or TH6/7 (red) or

TH33 (yellow) on the controller circuit board in the

electrical parts box.

(6) Loosen the clamp for the lead wire in the rear of the

electrical parts box.

(7) Pull out the thermistor <Outdoor pipe> (TH3), (TH33) and

thermistor <Outdoor 2-phase pipe> (TH6) from the

sensor holder.

Note: Replace the thermistor <Outdoor 2-phase pipe> (TH6)

and the thermistor <Outdoor> (TH7) together since

they are combined.

Refer to No. 5. to remove the thermistor <Outdoor> (TH7).

3. Removing the electrical parts box

(1) Remove the service panel. (See Photo 2)

(2) Remove the top panel. (See Photo 1)

(3) Remove the front panel. (See Photo 1)

(4) Disconnect the indoor/outdoor connecting wire from

terminal block.

(5)

Remove all the following connectors from controller circuit board;

fan motor, LEV, thermistor<Outdoor pipe>,

thermistor<Discharge>, thermistor<Outdoor 2-phase pipe>,

thermistor<Outdoor>, high pressure switch, 4-way valve

and bypass valve.

Pull out the disconnected wire from the electrical parts box.

• Fan motor (CNF1)

• LEV (LEV-A and LEV-B)

• Thermistor <Outdoor pipe> (TH3) (TH33)

• Thermistor <Discharge> (TH4)

• Thermistor <Outdoor 2-phase pipe, Outdoor> (TH6/7)

• High pressure switch (63H)

(6) Remove the terminal cover and disconnect the compressor

lead wire.

(7) Remove the electrical parts box fixing screws, 1 from the

front, the right and the rear side, and detach the electrical

parts box by pulling it upward.

Photo 5

Electrical parts box

Controller circuit

board (C.B.)

Electrical

parts box

fixing

screw

Terminal

block

(TB1)

Compressor (MC)

Terminal

cover

Photo 6

Thermistor

(TH6)

Clamp

Electrical

parts box

Thermistor

(TH3)

Thermistor

(TH33)

Summary of Contents for PUHZ-RP100VHA3



























































































































































































Search results

Summary of Contents for PUHZ-RP100VHA3

Reviews:

Brands by name

Popular brands

Mitsubishi Electric PUHZ-RP100VHA3, Service Manual

Search results

Summary of Contents for PUHZ-RP100VHA3

Reviews:

Brands by name

Popular brands