Mitsubishi Electric PLFY-P VFM-E1, Installation Manual

Page: 11 / 36

11
GB
Ŷ
Vane setting
No setting Step 1 Step 2
Step 4 Step 3
All
outlets Draft
reduction*
Step 5
3UHVVWKH>6(/(&7@EXWWRQWRVDYHWKHVHWWLQJV
A screen will appear that indicates the setting information is being
transmitted.
The setting changes will be made to the selected outlet.
The screen will automatically return to the one shown above (step 5)
when the transmission is completed.
Make the settings for other outlets, following the same procedures.
If all outlets are selected, ZLOO EH GLVSOD\HG WKH QH[W WLPH WKH XQLW
goes into operation.
Navigating through the screens
‡ 7RJREDFNWRWKH0DLQPHQX ......................... >0(18@EXWWRQ
‡ 7RUHWXUQWRWKHSUHYLRXVVFUHHQ .................... >5(7851@EXWWRQ
Ŷ
&RQ¿UPDWLRQSURFHGXUH
F1 F2 F3 F4
Manual vane angle
Input display:
Address Check
M-NET address
Identify unit Check button
F1 F2 F3 F4
Manual vane angle
Return:
M-NET address
Function setting for unit
with vane fully open.
F1 F2 F3 F4
Manual vane angle
Return:
No communication
Check Unit state.
Ŷ
Manual vane angle
F1 F2 F3 F4
Main
Main display:
Cursor Page
Main menu
Maintenance
Initial setting
Service
F1 F2 F3 F4
Maintenance menu
Main menu:
Cursor
Auto descending panel
Manual vane angle
3D i-See sensor
F1 F2 F3 F4
Manual vane angle
Input display:
Address Check
M-NET address
Identify unit Check button
F1 F2 F3 F4
Manual vane angle
Manual vane angle
Select:
Setting
Outlet Angle
1 Select "Maintenance" from the Main
PHQX DQG SUHVV WKH >6(/(&7@
button.
2
Select "Manual vane angle" with
WKH >)@ RU >)@ EXWWRQ DQG SUHVV
WKH>6(/(&7@EXWWRQ
(OHFWULFDOZRUN
3
Select the "M-NET address" for
the units to whose vanes are to be
IL[HG ZLWK WKH >)@ RU >)@ EXWWRQ
DQGSUHVVWKH>6(/(&7@EXWWRQ
3UHVVWKH>)@EXWWRQWRFRQ¿UPWKH
unit.
The vane of only the target indoor
unit is pointing downward.
1 Select the "M-NET address" for
the units to whose vanes are to be
¿[HGZLWKWKH>)@RU>)@EXWWRQ
3UHVV WKH >)@ EXWWRQ WR FRQILUP
the unit.
2
$IWHU SUHVVLQJ WKH >)@ EXWWRQ
wait approximately 15 seconds,
and then check the current state
of the air conditioner.
ĺ7KHYDQHLVSRLQWLQJGRZQZDUG
ĺ7KLVDLUFRQGLWLRQHULVGLVSOD\HG
on the remote controller.
ĺ$OORXWOHWVDUHFORVHGĺ3UHVV
WKH >5(7851@ EXWWRQ DQG FRQWLQ -
ue the operation from the begin-
ning.
ĺ 7KH PHVVDJHV VKRZQ WR WKH
OHIW DUH GLVSOD\HG ĺ 7KH WDUJHW
device does not exist at this refrig-
erant address.
‡ 3UHVVWKH>5(7851@EXWWRQWRUH -
turn to the initial screen.
3 Change the "M-NET address" to
the next number.
‡ 5HIHU WR VWHS
1
to change the
"M-NET address" and continue
ZLWKWKHFRQ¿UPDWLRQ
4
The current vane setting will appear.
Select the desired outlets from 1
WKURXJKZLWKWKH>)@RU>)@EXWWRQ
‡2XWOHWDQG
4, (all outlets)"
3UHVVWKH>)@RU>)@EXWWRQWRJR
through the option in the order of
"No setting (reset)," "Step 1", "Step
2", "Step 3", "Step 4", "Step 5" and
“Draft reduction*”.
Select the desired setting.
* Draft reduction
The airflow direction for this
setting is more horizontal than the
airflow direction for the “Step 1”
setting in order to reduce a drafty
feeling. The draft reduction can be
set for only 1 vane.