Mitsubishi Electric PLA-RP100BA, Operation Manual

Page: 8 / 26

8
Reset 1
horizontal
2 3 4 5
Note: “0” indicates all outlets.
Horizontal airflow
Downward
Outlet No.3
Outlet No.4
Outlet No.2
Outlet No.1
MITSUBISHI
ELECTRIC
label
Remote controller setting
The airflow direction of this outlet
is controlled by the airflow direc -
tion setting of remote controller.
Fixed
The airflow direction of this outlet is fixed
in particular direction.
* When it is cold because of direct
airflow, the airflow direction can be fixed
horizontally to avoid direct airflow.
3. Operation
<Returning to the Main menu>
F1 F2 F3 F4
Main
Main display:
Cursor Page
Main menu
Vane·Louver·Vent. (Lossnay)
High power
Timer
Weekly timer
OU silent mode
Note:
●
During swing operation, the directional indication on the screen
does not change in sync with the directional vanes on the unit.
●
Available directions depend on the type of unit connected.
●
In the following cases, the actual air direction will differ from the
direction indicated on the remote controller display.
1. While the display is in “STAND BY” or “DEFROST” states.
2. Immediately after starting heat mode (while the system is wait -
ing for the mode change to take effect).
3. In heat mode, when room temperature is higher than the tem -
perature setting.
< How to set the fixed up/down air direction (Only for
wired remote controller) >
Note:
●
This function cannot be set depending on the outdoor unit to be
connected.
• For PLA-(Z)RP. BA series, only the particular outlet can be fixed to
certain direction with the procedures below. Once fixed, only the set
outlet is fixed every time air conditioner is turned on. (Other outlets
follow UP/DOWN air direction setting of remote controller.)
■
Explanation of word
• “Refrigerant address No.” and “Unit No.” are the numbers given to
each air conditioner.
• “Outlet No.” is the number given to each outlet of air conditioner.
(Refer to the illustration below.)
• “Up/Down air direction” is the direction (angle) to fix.
Press the [RETURN] button to go
back to the Main menu.
<Display of unsupported functions>
The message at left will appear if
the user selects a function not sup-
ported by the corresponding indoor
unit model.
F1 F2 F3 F4
Title
Not available
Unsupported function
Return:
3.5.2 Vane·Vent. (Lossnay)
<Accessing the menu>
F1 F2 F3 F4
Main
Main display:
Cursor Page
Main menu
Vane·Louver·Vent. (Lossnay)
High power
Timer
Weekly timer
OU silent mode
Select "Vane·Louver·Vent. (Loss-
nay)" from the Main menu (refer to
page 7), and press the [SELECT]
button.
<Vane setting>
F1 F2 F3 F4
Fri
Swing Off Off
Louver Vent. Vane
Cool
Room
Auto Set temp.
Mode Temp. Fan
Fri
<Vent. setting>
F1 F2 F3 F4
Fri
Low
Vent.
Press the [F1] or [F2] button to go
through the vane setting options:
"Auto", "Step 1", "Step 2", "Step 3",
"Step 4", "Step 5" and "Swing".
Select the desired setting.
Auto
Auto
Swing
Step 1 Step 2
Step 4 Step 3
Swing
Step 5
Select "Swing" to move the vanes
up and down automatically.
When set to "Step 1" through "Step
5", the vane will be fixed at the se -
lected angle.
• under the vane setting icon
This icon will appear when the
vane is set to "Step 2" to "Step 5"
and the fan operates at "Mid 1" to
"Low" speed during cooling or dry
operation (depends on the mod-
el).
The icon will go off in an hour, and
the vane setting will automatically
change.
Press the [F3] button to go through
the ventilation setting options in the
order of "Off", "Low", and "High".
* Settable only when LOSSNAY unit
is connected.
Off Low High
Off Low High
• The fan on some models of indoor
units may be interlocked with cer-
tain models of ventilation units.
RG79D506H06_EN.indd 8 2016/04/01 10:25:39