6
GB
3. How to Operate
The use of the sensor can be switched between on the indoor unit and on the remote controller.
The factory setting is the sensor on the indoor unit.
Refer to the Installation Manual for switching the sensor.
3.1. Screen Configuration
<Screen Types>
z
Function Selection of remote controller:
Set the functions and ranges available to the
remote controller (timer functions, operating
restrictions, etc.)
z
Set Day/Time:
Set the current day of the week or time.
z
Standard Control Screens: View and set the air conditioning system’s
operating status
z
Timer Monitor:
View the currently set timer (weekly timer, simple
timer, or Auto Off timer)
z
Timer Setup:
Set the operation of any of the timers (weekly timer,
simple timer, or Auto Off timer).
<How to change the screen>
A
: Hold down both the Mode button and the Timer On/Off button for 2 seconds.
B
: Press the Timer Menu button.
C
: Press the Mode (Return) button.
D
: Press either of the Set Time buttons (
or
).
3.2. Setting the Day of the Week and Time
Use this screen to change the current day of the week and time setting.
Note:
The day and time will not appear if clock use has been disabled at Function
Selection of remote controller.
<How to Set the Day of the Week and Time...>
1. Press the
or
Set Time button
a
to show display
2
.
2. Press the Timer On/Off (Set Day) button
9
to set the day.
* Each press advances the day shown at
3
: Sun
→
Mon
→
...
→
Fri
→
Sat.
3. Press the appropriate Set Time button
a
as necessary to set the time.
* As you hold the button down, the time (at
4
) will increment first in minute
intervals, then in ten-minute intervals, and then in one-hour intervals.
4. After making the appropriate settings at Steps 2 and 3, press the Filter
button
4
to lock in the values.
Note:
Your new entries at Steps 2 and 3 will be cancelled if you press the Mode
(Return) button
2
before pressing the Filter
button
4
.
5. Press the Mode (Return) button
2
to complete the setting procedure. This
will return the display to the standard control screen, where
1
will now show
the newly set day and time.
3.3. Using the Remote Controller
1. How to Start, Stop, Change the Mode, and Adjust
the Temperature
<To Start Operation>
Press the ON/OFF button
1
.
• The ON lamp
1
and the display area come on.
Note:
z
When the unit is restarted, initial settings are as follows.
<To Stop Operation>
Press the ON/OFF button
1
again.
• The ON lamp
1
and the display area go dark.
<Selecting the Mode>
With the unit running, press the Mode button
2
as many times as necessary.
• Each press switches operation to the next mode, in the sequence shown
below.
The currently selected mode is shown at
2
.
Note:
*1 Availability of this mode depends on the type of unit connected.
<To Change the Room Temperature Setting...>
To lower the temperature: Press the
Set Temperature button
3
.
To raise the temperature: Press the
Set Temperature button
3
.
• Each press changes the setting by 1 °C. The current setting is displayed at
3
.
• The available ranges are as follows. *1, *2
Note:
*1 Available ranges vary according to the type of unit connected.
*2 If temperature range limits have been set at Function Selection of remote
controller, the available ranges will be narrower than shown above. If you
attempt to set a value outside of the restricted range, the display will show a
message indicating that the range is currently restricted.
For information about how to set and clear these range limits, refer to section
3.4., item [4]–2 (3).
*3 If Function Selection of remote controller are set to display the temperature in
Fahrenheit. For information about how to select °C or °F , refer to section 3.4.,
item [4]–4 (1).
°F
°C
TIMER
MON
OFF
WEEKLY
SUN MON TUE WED THU FRI SAT
WEEKLY
°C
°C
TIME SUN
Function Selection of remote controller
Set Day/Time
Standard Control Screens
OFF
ON
A
D
C
B
C
B
Timer Monitor
Timer Setup
°C
°C
TIME SUN
PAR-21MAA
ON/OFF
FILTER
CHECK
OPERATION
CLEAR
TEST
TEMP.
MENU
BACK
DAY
MONITOR/SET
CLOCK
ON/OFF
2
4
9
1
a
Day of the Week &
Time display
TIME SUN
2
3
4
Day of the Week Setting
Time Setting
Remote Controller settings
Mode
Last operation mode
Temperature setting
Last set temperature
Fan speed
Last set fan speed
COOL mode
HEAT mode
FAN
During the indoor temperature control with
Fresh Air Intake type units
19 ~ 30 °C (66 ~ 87 °F) *3
Conditions other than above
14 ~ 30 °C (57 ~ 87 °F) *3
17 ~ 28 °C
(63 ~ 83 °F) *3
Cannot be set.
°C
°C
PAR-21MAA
ON/OFF
FILTER
CHECK
OPERATION
CLEAR
TEST
TEMP.
MENU
BACK
DAY
MONITOR/SET
CLOCK
ON/OFF
2
7
2
3
3
8
6
4
5
8
7
1
1
5
6
COOL
FAN
HEAT
*1
Ventilate
*1
00gb_WT05475X02_7.book Page 6 Tuesday, June 16, 2009 12:33 PM
