background image

1

2

3

4

51

TB7

TB3

01

TB5

TB15

02

TB5

TB15

03

TB5

TB15

54

TB7

TB3

06

TB5

TB15

MA

05

TB5

TB15

04

OC

IC

IC

IC

OC

IC

IC

IC

TB5

TB15

CN41

CN40

 CAUTION

Do not install in any steamy place such a bathroom or kitchen.

Avoid any place where moisture is condensed into dew. Doing so
may cause an electric shock or a malfunction.

Do not install in any place where acidic or alkaline solution or
special spray are often used.

Doing so may cause an electric shock or malfunction.

Use standard wires in compliance with the current capacity.

A failure to this may result in an electric leakage, heating or fire.

Do not touch any PCB (Printed Circuit Board) with your hands
or with tools. Do not allow dust to collect on the PCB.

Doing so may cause fire or an electric shock.

Do not touch any control button with your wet hands.

Doing so may cause an electric shock or a malfunction.

Do not press any control button using a sharp object.

Doing so may cause an electric shock or a malfunction.

Never contact the power supply with the control wiring termi-
nals.

Doing so will certainly cause the controller to catch fire.

Building Air Conditioning Control System

Signal Receiving Unit

PAR-FA32MA

Installation Manual

This installation manual contains only the description of how to install the Signal Receiving Unit PAR-FA32MA. For information about
how to wire and how to install air conditioning units, see the installation manual for them.
For your safety, first be sure to read 

“  1   Safety Precautions  ”

 described below thoroughly and then install the Signal Receiving Unit PAR-

FA32MA correctly.

1

Safety Precautions

The following two symbols are used to denote dangers that may be caused by incorrect use and their degree:

 

WARNING

This symbol denotes what could lead to serious injury or death if you misuse the PAR-FA32MA.

 

CAUTION

This symbol denotes what could lead to a personal injury or damage to your property if you misuse the PAR-FA32MA.

After reading this installation manual, keep it in a place where the final user can see it anytime.
When someone moves, repairs or uses the PAR-FA32MA, make sure that this manual is forwarded to the final user.

 WARNING

WT04753X01

Do not install in any place exposed to flammable gas leakage.

Flammable gases accumulated around the body of PAR-FA32MA
may cause an explosion.

Do not use in any special environment.

Using in any place exposed to oil (including machine oil), steam and
sulfuric gas may deteriorate the performance significantly or give
damage to the component parts.

Wire so that it does not receive any tension.

Tension may cause wire breakage, heating or fire.

Completely seal the wire lead-in port with putty etc.

Any dew, moisture, cockroaches, insects entering the unit may cause
an electric shock or a malfunction.

Do not wash with water.

Doing so may cause an electric shock or a malfunction.

Do not install in any place at a temperature of more than 40

°

C

(104 

°

F) or less than 0 

°

C (32 

°

F) or exposed to direct sunlight.

Ensure that installation work is done correctly following this
installation manual.

Any deficiency caused by installation may result in an electric shock
or fire.

All electrical work must be performed by a licensed technician,
according to local regulations and the instructions given in this
manual.

Any lack of electric circuit or any deficiency caused by installation
may result in an electric shock or fire.

Do not move and re-install the PAR-FA32MA yourself.

Any deficiency caused by installation may result in an electric shock
or fire.
Ask your distributor or special vendor for moving and installation.

To dispose of this product, consult your dealer.

GB

2

Confirming the Supplied Parts

Check that the box includes the following parts in addition to this installation manual:

(5) Install the lower case on the switch box or directly on the wall.

When installing on the switch box, seal the con-
nections between the switch box and wiring
pipe with putty.

When using the switch box

When opening a hole using a drill for Signal Receiving Unit cord (or tak-
ing the cord out of the back of the Signal Receiving Unit), seal that hole
with putty.

When routing the cord via the portion cut off from the upper case, equally
seal that portion with putty.

When installing directly on the wall

5

How To  Install

(1) Choose a place in which to install the Signal Receiving Unit (switch box).

Be sure to observe the following steps:

1

When installing on either the switch box or the wall,allow space around the Signal
Receiving Unit as shown in the figure on the right.

2

When installing the Signal Receiving Unit to the swich box, the Signal Receiving Unit
slipped downward for 6.5 mm (1/4 inch) as right illustrated.

3

Parts which must be supplied on site.

Switch box for one unit
Thin-copper wiring pipe
Lock nut and bushing

4

lnstall the unit on the wall or ceiling where the signal is received from the remote
controller.
(Refer to the below illustration)

4

Setting the Pair Number & Main/Sub Switch

Setting pair number of the wireless remote controller and the Signal Receiving Unit.
Set switch position of the Signal Receiving Unit as follows.
Refer to the installation manual that came with the wireless remote controller for how to set pair numbers of wireless remote controllers.

“0”

“0”

“1”

“1”

“2”

“2”

“3”

“3”

“0”

“0”

“0”

“0”

“0”

“0”

“0”

“0”

“0”

3

Example of System Configuration

The remote controller wire is connected to CITY MULTI System (C type or later).
(In case of CITY MULTI System)

Group 1

Group 2

Group 3

90˚

Max. 7m (22 ft)

Install the Signal Receiving Unit where is watched from any position.

NOTE: lf the Signal Receiving Unit is installed near a fluoresent lamp specially inverter type,signal interception may occur.

Be careful for installing the Signal Receiving Unit or replacing the lamp.

(2) Install the remote control cord to the terminal block (No polarity).

Remote controller Cord

ø10 (13/32)

When consealing wire, the hole ø10 (13/32) to push a remote
control cord through is nesessary on the ceiling.

Signal Receiving Unit

(3) Installing hole when the Signal Receiving Unit is installed on the wall direct.

Cut the thin-wall portion inside the bottom case (oblique section) by a knife or a nipper.

Take out the connected remote control cord to the terminal brock through this space.

(4) Seal the Signal Receiving Unit cord lead-in hole with putty in order to prevent the possible entry of dew, water

droplets, cockroaches, other insects, etc.

Insert the minus screwdriver toward the
arrow pointed and wrench it to remove the cover.
A flat screwdriver whose width of blade is between
4 and 7 mm (5/32 - 9/32 inch) must be used.

Remote control cord

Push a remote control cord
through the wires installed hole.

¡

Thin-wall protion

Bottom case

200 (7-7/8)

Wall

Remote control
cord (Accessory)

Wiring pipe

Locknut

Bushing

Switch box

Seal around here
with putty

Seal around here
with putty

Remote control cord

Seal around here
with putty

(6) Install the cover

6

Test Run

Refer to the installation manual for wireless remote controller for how to perform the test run.

Ask your dealer or technical representative to install the unit.

Any deficiency caused by your own installation may result in an elec-
tric shock or fire.

Install in a place which is strong enough to withstand the weight
of the PAR-FA32MA.

Any lack of strength may cause the PAR-FA32MA to fall down, re-
sulting in personal injury.

Firmly connect the wiring using the specified cables. Carefully
check that the cables do not exert any force on the terminals.

Improper wiring connections may produce heat and possibly a fire.

Never modify or repair the PAR-FA32MA by yourself.

Any deficiency caused by your modification or repair may result in
an electric shock or fire.
Consult with your dealer about repairs.

Separate setting
Each unit can only be operated by its own wireless
remote controller.

Single setting
All the units can be operated by a single wireless remote
controller.

2

-2 When setting in different rooms.

Assing a different number to each wireless remote
controller and all the Signal Receiving Unit
(Leave the setting as purchase)

NOTE: With group operation with a different cooling system, wire only the MA remote controller wiring terminal block (TB15).

Do not wire the indoor/outdoor transmission terminal block (TB5).

70 (2-3/4)

6,5 

( 1/4

)

83,5

±

0,4 

( 3-9/32

)

Signal receiving
unit external

Center of
Switch box

Switch box

Installation pitch

Unit : mm (in)

Protrusion
(pillar, etc)

2

Setting example

2

-1 When setting in same room.

(1) Signal Receiving Unit ......................................................... 1
(2) Remote control cord (2 core 3 m (9 ft)) .............................. 1

(3) Screw (M4 

×

 30) .................................................................. 2

(4) Wood screw (4.1 

×

 16) ........................................................ 2

Example: Ceiling cassette type, Ceiling cosealed type

NOTE: Extended remote controller cords are not supplied with this equipment and must therefore be procured locally by the customer.

Use electrical cable in accordance with the following specifications.
• 0.3 - 1.25 mm

2

 (Stranded 22 to 16 AWG) twin-core cable (CVV, CVS, VVF)

Use a maximum of 1.25 mm

2

 (16 AWG) cable for signal receiving unit wiring. 0.75 mm

(18 AWG) wiring is recommended for ease of installation.

See the installation manual supplied with the outdoor unit for details of maximum wiring distances.

(1) Change the pair number switch to set the pair number.

1

Pair number
To fix the Signal Receiving Unit which operates from the wireless remote controller.
10 kinds of setting (0 - 9) are available for the wireless remote controller and Signal Receiving Unit.

  Adapt a pair number to the using wireless remote controller.

1 2

3

0

9

8

7 6 5 4

3

2

1

PAR-FA32MA

Pair No. of receiver
matches that of re-
mote controller.

Main/Sub switch
(Factory setting
“main”)

Seal

Signal Receiving Unit
(Externals removing the cover)

Pair number switch
(Factory setting “0”)

0

9

8

7

6

5

4

3

2

1

1

Wiring from signal receiving unit.
· Connected to MA remote controller wiring terminal block (TB15) on the indoor unit. (The terminal block has no polarities.)

2

With group operation (group 3 and group 4 above).
· After wiring the MA remote controller wiring terminal block (TB15) on the group operation indoor unit, connect to the indoor unit

with the lowest address within the group.

3

The signal receiving unit and the MA remote controller may be used together (group 4 above).
· Set the MA remote controller as “Main”, and the signal receiving unit as “Sub”.
· When other types of remote controllers are used, refer to section “  7  Possible Combinations of Signal Receiving Units and

Remote Controllers ”.

See the installation manual supplied with the outdoor unit for details of setting up indoor (IC) and outdoor (OC) units.

See the relevant equipment manual for details of setting up the central controller and transmission line power supply unit.

Central management transmission line
(M-NET transmission line)

Indoor and outdoor transmission lines
(M-NET transmission line)

MA remote controller cable

Signal receiving unit

(Main)

(Main)

(Main)

(Main)

(Sub)

(2) Main/Sub switch settings (leave the initial “Main” setting when not using the MA remote controller).

Set the Main/Sub switch when using with the MA remote controller (PAR-20MAA).
Set the signal receiving unit to “Sub” and the MA remote controller (PAR-20MAA) to “Main”.

Group 4

7

Possible Combinations of Signal Receiving Units and Remote Controllers

When the Signal Receiving Unit and other types of remote controller are used together, the following combinations must be used.

Possible combinations of remote controllers

Indoor unit function

• Models with 1

°

F tempera-

ture setting

• Models with maintenance

function

• Models without 1

°

F tem-

perature setting

• Models without mainte-

nance function

Main remote controller

MA(20)/RX(31)

RX
RX

MA(21)

RX

Sub remote controller

RX

MA(20)/RX(31)

RX
RX

MA(21)

Availability

Available

The temperature cannot be set in increments
of 1

°

F using wireless remote controller.

Not available

Available
Available

Not available

Available

This product is designed and intended for use in a residential, commercial or light-industrial environment.
The product at hand is based on the following EU regulations:

Electromagnetic Compatibility Directive 89/336/EEC

Replace CN41

with CN40.

Leave CN41 as it is.

NOTE:
• No power supply lines are shown and only the trans-

mission lines are shown in the above wiring example.

• Provide shield grounding of M-NET transmission line

at one arbitrary point.

All combinations shown above

RX:

Signal Receiving Unit (PAR-FA32MA)

RX(31): PAR-FA31MA (Old model)

MA(20): MA remote controller (PAR-20MAA)

MA(21): MA remote controller (PAR-21MAA)

A main remote controller and a sub remote con-
troller can be connected to each group.

Screw (M4 

×

 30)

When installing the lower case directly on
the wall or the ceiling, use wood screws.

Indoor unit

Summary of Contents for PAR-FA32MA

Page 1: ...re so that it does not receive any tension Tension may cause wire breakage heating or fire Completely seal the wire lead in port with putty etc Any dew moisture cockroaches insects entering the unit may cause an electric shock or a malfunction Do not wash with water Doing so may cause an electric shock or a malfunction Do not install in any place at a temperature of more than 40 C 104 F or less th...

Page 2: ...ing the cover Pair number switch Factory setting 0 0 9 8 7 6 5 4 3 2 1 1 Wiring from signal receiving unit Connected to MA remote controller wiring terminal block TB15 on the indoor unit The terminal block has no polarities 2 With group operation group 3 and group 4 above After wiring the MA remote controller wiring terminal block TB15 on the group operation indoor unit connect to the indoor unit ...

Page 3: ...Cord ø10 13 32 When consealing wire the hole ø10 13 32 to push a remote control cord through is nesessary on the ceiling Signal Receiving Unit 3 4 Insert the minus screwdriver toward the arrow pointed and wrench it to remove the cover A flat screwdriver whose width of blade is between 4 and 7 mm 5 32 9 32 inch must be used Remote control cord Push a remote control cord through the wires installed ...

Page 4: ...ound here with putty 6 Install the cover 6 Test Run Refer to the installation manual for wireless remote controller for how to perform the test run on c 7 Possible Combinations of Signal Receiving Units and Remote Controllers When the Signal Receiving Unit and other types of remote controller are used together the following combinations must be used Possible combinations of remote controllers Indo...

Reviews: