Mitsubishi Electric MHK2 Installation Manual Download Page 14

Page: 14 / 17

Heat

Auto

Vane

Mode

Menu

Fan

Key Features

Note:

The screen will wake up by pressing the center area of the displayed temperature.

The screen will stay lit for 10 seconds.

System Status Information

Cool On, Heat On, Standby.

Schedule Information

Following time-based

temperature control.

Desired Temperature

Displays the current desired

temperature setting.

Indoor Temperature

Displays the current indoor

temperature.

Indoor Temperature

Reminder:

The indoor temperature

display will show the

temperature from the indoor

unit, the MHK2 controller,

indoor air sensor(s), or an

average of all them. You

confirm and configure this

setting during installation

setup.

Vane

Touch to select air direction:

Auto, Swing, Ceiling, High,

Middle, Low, Floor.

Mode

Select system Mode: Heat,

Cool, Dry, Fan, Auto, Off.

Lock

Indicates the screen is

locked: Full Lock, Partial

Lock, and ISU-based locks.

Full and Partial Lock can be

unlocked with a PIN.

RedLINK™ Wireless

Communication Status

Indicates if the controller is

connected to the RedLINK™

interface and communicating

correctly.

Connection Status

Information

Indicates if the MIFH2

RedLINK™ Wireless Receiver

is connected to the Mitsubishi

Electric Wireless Interface 2

and kumo cloud

Messaging

Shows device setup options,

menu options, reminders,

schedule overrides.

Schedule Period

Shows schedule period: Wake,

Leave, Return, Sleep.

Fan

Select Fan speeds: Auto, 1-5.

Menu

Touch to display options.

Start here to set a program

schedule.

Note: Long press the Menu

button for 5 seconds to

access Advanced Menu

options.

Time, ISU #,

or Alert #

33-00446EFS_B.indd 14

10/17/2019 3:09:01 PM

Summary of Contents for MHK2


















Search results

Summary of Contents for MHK2

Reviews:

Brands by name

Popular brands

Mitsubishi Electric MHK2, Installation Manual

Search results

Summary of Contents for MHK2

Reviews:

Brands by name

Popular brands