Mitsubishi Electric MHK2 Installation Manual Download

Page: 1 / 17

RedLINK™ Wireless
Remote Controller Kit

Installation Manual

MHK2:

MRCH2 Controller, MIFH2
Receiver, and MRC2 Cable

DISCONNECT POWER

BEFORE BEGINNING INSTALLATION

Can cause electrical shock or equipment damage.

Must be installed by a trained, experienced technician

Read these instructions carefully. Failure to follow these instructions can damage the product or cause a

hazardous condition.

Installation at a Glance

This manual covers the installation and setup of the MHK2 Remote Controller with Mitsubishi Electric

indoor units.
Before you begin, you must attach the cable to the CN105 connector on the indoor unit control

board, then follow the steps in this document.

Note:

Remote Controllers are linked to specific indoor units. Each indoor unit must have a

dedicated Remote Controller and Wireless Receiver.

Note:

Your device's PIN code is your date code added to 1234. For example, a date code of

2010 plus 1234 would give you a device PIN of 3244.

https://mhk2.meushvac.com/

1-800-433-4822

MHK2 is compatible
with kumo cloud

when

connected with the Wireless

Interface 2 or later.

RedLINK

Technology

33-00446EFS_B.indd 1

10/17/2019 3:08:58 PM

Summary of Contents for MHK2


















Search results

Summary of Contents for MHK2

Reviews:

Related manuals for MHK2

Brands by name

Popular brands

Mitsubishi Electric MHK2, Installation Manual

Search results

Summary of Contents for MHK2

Reviews:

Related manuals for MHK2

Brands by name

Popular brands