Mitsubishi Electric MELSERVO J5 Series User Manual Download Page 101 | Manualshive

Page: 101 / 126

background image

13 Profile Position Mode Objects

13.6 [Profile velocity (Obj. 6081h)]

99

13

13.6

[Profile velocity (Obj. 6081h)]

[Profile velocity (Obj. 6081h: 00h)]

Description

Set the speed command used in the profile position mode (pp). If [Pr. PT02.7 Internal position command - Process speed
selection] is set to "0" and the set speed exceeds 8000 r/min (or mm/s), the servo motor speed is clamped at 8000 r/min (or
mm/s). When changing the maximum value of "Range" to the permissible speed, set [Pr. PA28.4 Speed range limit selection]
to "1". The description of the object varies as shown in the table below, depending on the combination of the setting of [Pr.
PT01.1 Speed/acceleration/deceleration unit selection] and the connected servo motor.

13.7

[Profile acceleration (Obj. 6083h)]

[Profile acceleration (Obj. 6083h: 00h)]

Description

Set the acceleration time constant or the acceleration used in the profile position mode (pp) and the profile velocity mode (pv).
The description of the object varies as shown in the table below depending on [Pr. PT01.1 Speed/acceleration/deceleration
unit selection]. When [Pr. PT01.1] is set to "0", set the time required for the servo motor to reach the rated speed. The value
that can be set varies for each control mode.

*1 When "0" is set, the servo motor accelerates in accordance with the setting value of [Pr. PT49].

Data Type

Access

Mapping

Default

Range

Units

Save

Parameter

U32

RW

RXMAP

Refer to the
following.

0 to maximum
speed

vel units

Possible

Refer to the
following.

[Pr. PT01.1]

Connected servo motor

Default

Units

Parameter

0 (encoder unit)

Rotary servo motor

10000

0.01 r/min

[Pr. PT65]

Linear servo motor

0.01 mm/s

1 (command unit)



0

pulse/s

[Pr. PV01]

Data Type

Access

Mapping

Default

Range

Units

Save

Parameter

U32

RW

RXMAP

Refer to the
following.

Refer to the
following.

acc units

Possible

Refer to the
following.

[Pr. PT01.1]

Default

Range

Units

Parameter

0 (encoder unit)

100

pp: 0 to 20000
pv: 0 to 50000

ms

[Pr. PT49]

1 (command unit)

0

0 to 4294967295

pulse/s

2

[Pr. PV05]

«
...
99
100
101
102
103
...
»

Summary of Contents for MELSERVO J5 Series































































































































Reviews:

No comments

Related manuals for MELSERVO J5 Series

Brand: Radio Shack Pages: 20

Brand: Gallien-Krueger Pages: 19

Brand: DAD Pages: 24

Bassman Bassman 100

Brand: Fender Pages: 20

Brand: Fender Pages: 156

G-DEC 3 Thirty & Fifteen

Brand: Fender Pages: 24

Brand: Kathrein Pages: 8

Brand: Kathrein Pages: 8

Brand: Alpha Pages: 4

Brand: Crown Pages: 1

Sonic Frontiers Power 1

Brand: Sonic Frontiers Pages: 17

Brand: Blaupunkt Pages: 4

Brand: Key Digital Pages: 1

Brand: Phoenix Gold Pages: 2

NAC 112 - ISSUE 2

Brand: NAIM Pages: 30

Brand: Rotel Pages: 16

Brand: NAD Pages: 2

Brand: Genie Pages: 5

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands