manualshive.com logo in svg

Mitsubishi Electric MELSEC iQ-R CC-Link IE TSN, User Manual

The Mitsubishi Electric MELSEC iQ-R CC-Link IE TSN is an advanced automation controller that ensures efficient and seamless communication within industrial systems. Unlock the full potential of this powerful device with our comprehensive user manual, available for free download from manualshive.com. Master this cutting-edge technology with ease.

Share
Download
background image

4  TROUBLESHOOTING

4.3  Checking the Network Status

169

4

4.3

Checking the Network Status

This section describes troubleshooting to check the status of the network by executing diagnostics and operation tests using 
the engineering tool.

CC-Link IE TSN/CC-Link IE Field Diagnostics

For CC-Link IE TSN, perform status monitoring, operation tests, or others.

Precautions

In the following cases, the CC-Link IE TSN/CC-Link IE Field diagnostics cannot start.
 • The RJ71GN11-T2 is not connected to CPU modules specified on the "Specify Connection Destination Connection" 

window.

 • In CPU parameters of CPU modules specified on the "Specify Connection Destination Connection" window, "Link Direct 

Device Setting" of "Memory/Device Setting" is not "Extended Mode (iQ-R Series Mode)".

 • "Module Operation Mode Setting" under "Application Settings" of the RJ71GN11-T2 is not in the online mode.
 • The error code 20E0H occurs.
 • The engineering tool is not connected to a station with the same communication speed as the master station.
 • The network topology of the diagnostics destination does not support the version of the engineering tool or module.

Diagnostic items

When starting the CC-Link IE TSN/CC-Link IE Field diagnostics by specifying "No Specification" in "Other Station Setting" on 
the "Specify Connection Destination Connection" window, the following items can be used.

: Diagnosed 

: Diagnosed with restrictions 

: Not diagnosed

*1 If the setting on the "Specify Connection Destination Connection" window of the engineering tool is as follows, remote operation cannot 

be executed with "All Stations Specified".
Connection via Ethernet with the selections "Ethernet Board" for the personal computer-side I/F and "CC IE TSN/Field Module" for the 
programmable controller-side I/F

Item

Overview

Connection destination of 
engineering tool

Reference

Master station Local station

Status 
monitor

Network map

Check if any errors are being caused by 
the devices and cables that configure the 
network. In addition, check the operating 
status of each station.

Page 174 "CC-Link IE 
TSN/CC-Link IE Field 
Diagnostics" window

Data Unlinked

Check that there is no station that is set on 
an actual network.

Selected Station 
Communication Status 
Monitor

Check details of, or actions for, errors that 
occurred in a selected station.

Operation 
Test

Communication Test

Check whether outgoing/incoming paths 
of transient transmission between the own 
station and the communication target are 
correct.

Page 179 
Communication Test

Information 
Confirmation/
Setting

Station Information List

Check information of the slave stations 
which are performing data link in list form.

Page 181 Station 
Information List

Selected 
Station 
Operation

Remote Operation

Operate remotely from the engineering 
tool to slave stations.

*1

*1

Page 182 Remote 
Operation

Summary of Contents for MELSEC iQ-R CC-Link IE TSN











































































































































































































































































































































Reviews:

No comments

Related manuals for MELSEC iQ-R CC-Link IE TSN

unicore UM960 Installation And Operation User Manual preview
UM960
Brand: unicore Pages: 25
unicore UM960L Installation And Operation User Manual preview
UM960L
Brand: unicore Pages: 24
KEENZ Class Instruction Manual preview
Class
Brand: KEENZ Pages: 24
FrSky Taranis Q X7S Manual preview
Taranis Q X7S
Brand: FrSky Pages: 2
Jafar 2109 Operation And Maintenance Manual preview
2109
Brand: Jafar Pages: 10
Baby Jogger CITY ELITE SINGLE Instruction Manual preview
CITY ELITE SINGLE
Brand: Baby Jogger Pages: 3
Caen V793 Technical Information Manual preview
V793
Brand: Caen Pages: 20
KaRo QS Series Manual preview
QS Series
Brand: KaRo Pages: 12
TCS CS-105 Quick Start Manual preview
CS-105
Brand: TCS Pages: 16
Eaton SCD24 Installation Manual preview
SCD24
Brand: Eaton Pages: 8
ABB RHDE250 Operating Instruction preview
RHDE250
Brand: ABB Pages: 44
Omega CNI16D Quick Start preview
CNI16D
Brand: Omega Pages: 2
Zmotion ZMC408SCAN Hardware Manual preview
ZMC408SCAN
Brand: Zmotion Pages: 34
Raynor Smart Control Panel 880RGD Quick Manual preview
Smart Control Panel 880RGD
Brand: Raynor Pages: 4
Click2Enter Click2Enter-I Operating & Installation Instructions Manual preview
Click2Enter-I
Brand: Click2Enter Pages: 34
Comet S0841 Instruction Manual preview
S0841
Brand: Comet Pages: 9
Acumen Model L Operating Instructions Manual preview
Model L
Brand: Acumen Pages: 6
PCB Piezotronics 482B06 Installation And Operating Manual preview
482B06
Brand: PCB Piezotronics Pages: 12

Brands by name

Popular brands

Load more brands