manualshive.com logo in svg

Mitsubishi Electric MELSEC iQ-F FX55-ASL-M, User Manual

The Mitsubishi Electric MELSEC iQ-F FX55-ASL-M is a high-performance automation controller designed for efficient and precise control in industrial applications. Unlock the full potential of this product by downloading the comprehensive User Manual, available for free at manualshive.com. Access detailed instructions and optimize your productivity today.

Share
Download
background image

14

• FX3 intelligent function module

Generic term for FX3U-4AD, FX3U-4DA, FX3U-4LC, FX3U-1PG, FX3U-2HC, FX3U-16CCL-M, FX3U-64CCL, 
and FX3U-128ASL-M

Expansion board

Generic term for board for FX5U CPU module

• Communication board

Generic term for FX5-232-BD, FX5-485-BD, and FX5-422-BD-GOT

Expansion adapter

Generic term for adapter for FX5 CPU module

• Communication adapter

Generic term for FX5-232ADP and FX5-485ADP

• Analog adapter

Generic term for FX5-4AD-ADP, FX5-4DA-ADP, FX5-4AD-PT-ADP, and FX5-4AD-TC-ADP

Bus conversion module

Generic term for Bus conversion module (extension cable type) and Bus conversion module (extension 
connector type)

• Bus conversion module (extension cable 

type)

Different name for FX5-CNV-BUS

• Bus conversion module (extension 

connector type)

Different name for FX5-CNV-BUSC

Connector conversion module

Generic term for Connector conversion module (extension cable type) and Connector conversion module 
(extension connector type)

• Connector conversion module (extension 

cable type)

Different name for FX5-CNV-IF

• Connector conversion module (extension 

connector type)

Different name for FX5-CNV-IFC

Extended extension cable

Generic term for FX5-30EC and FX5-65EC

Connector conversion adapter

Different name for FX5-CNV-BC

Battery

Different name for FX3U-32BL

Peripheral device

Generic term for engineering tools and GOTs

GOT

Generic term for Mitsubishi Electric Graphic Operation Terminal GOT1000 and GOT2000 series

■

Software packages

Engineering tool

The product name of the software package for the MELSEC programmable controllers

GX Works3

The product name of the software package, SWnDND-GXW3, for the MELSEC programmable controllers (The 
'n' represents a version.)

■

AnyWireASLINK

AnyWireASLINK

A reduced wiring network where sensors at the end of a control system are connected to a programmable 
controller.

ASLINKAMP

A genetic term for sensor amplifiers that have an AnyWireASLINK interface

ASLINKER

A genetic term for I/O devices that have an AnyWireASLINK interface

ID

A parameter to identify whether the module is an input module or output module based on its address
Output slave module ID: Address
ID of the input slave module or I/O combined slave module: A 200H

RAS

The abbreviation for Reliability, Availability, and Serviceability. This term refers to usability of automated 
equipment.

Address

A parameter assigned to a slave module to identify each node on the AnyWireASLINK network

Address writer

A hand-held device to read/write parameters (including addresses) from/to a slave module

Slave module

A generic term for modules that communicate data with the FX5-ASL-M

Terminating unit

A waveform shaper

Power cable (24V, 0V)

A cable that connects a 24 V DC external power supply to the FX5-ASL-M.
This cable is also used when the isolation (4-line) type slave module and FX5-ASL-M are connected.

Transmission cycle time

A data sampling interval

Transmission cable (DP, DN)

A signal cable that connects between a slave module and the FX5-ASL-M

Terms

Description

Summary of Contents for MELSEC iQ-F FX55-ASL-M

































































































Reviews:

No comments

Related manuals for MELSEC iQ-F FX55-ASL-M

Baby Trend ST50 Instruction Manual preview
ST50
Brand: Baby Trend Pages: 10
Jeep Liberty Instruction Sheet preview
Liberty
Brand: Jeep Pages: 32
Accel 300+ Installation Instructions Manual preview
300+
Brand: Accel Pages: 8
Yardney Synergy Quick Start Manual preview
Synergy
Brand: Yardney Pages: 8
Danfoss FP735Si Installation Manual preview
FP735Si
Brand: Danfoss Pages: 20
Danfoss CP715 Si Installation & User'S Instructions preview
CP715 Si
Brand: Danfoss Pages: 36
Harpo BraillePen 12 Quick Start Manual preview
BraillePen 12
Brand: Harpo Pages: 35
Hardi HC 6500 Quick Manual preview
HC 6500
Brand: Hardi Pages: 2
IBM ServeRAID-MR10is User Manual preview
ServeRAID-MR10is
Brand: IBM Pages: 94
IBM ServeRAID-4 Ultra160 Series Installation Instructions Manual preview
ServeRAID-4 Ultra160 Series
Brand: IBM Pages: 20
IBM 8271 Nways Ethernet LAN Switch Manual preview
8271 Nways Ethernet LAN Switch
Brand: IBM Pages: 6
IBM 3174 Introduction Manual preview
3174
Brand: IBM Pages: 86
IBM 3745 Series Console Setup Manual preview
3745 Series
Brand: IBM Pages: 205
IBM N6000 Series Installation And Setup Instructions preview
N6000 Series
Brand: IBM Pages: 28
Samson 3277 Quick Manual preview
3277
Brand: Samson Pages: 2
M-Audio Axiom AIR 25 Service Manual preview
Axiom AIR 25
Brand: M-Audio Pages: 26
M Climate Bobbie Installation Instructions Manual preview
Bobbie
Brand: M Climate Pages: 12
Omnex R1300 Manual preview
R1300
Brand: Omnex Pages: 9

Brands by name

Popular brands

Load more brands