manualshive.com logo in svg

Mitsubishi Electric MELSEC FX2N-32DP-IF, Hardware Manual, Page: 6 / 54

Share
Download
Mitsubishi Electric MELSEC FX2N-32DP-IF Hardware Manual Download Page 6

FX2N-32DP-IF Profibus-DP Interface Unit

iv

Note’s on the Symbols Used in this Manual

At various times through out this manual certain symbols will be used to highlight points of
information which are intended to ensure the users personal safety and protect the integrity of
the equipment. Whenever any of the following symbols are encountered its associated note
must be read and understood. Each of the symbols used will now be listed with a brief
description of its meaning.

Hardware Warnings

1) Indicates that the identified danger 

WILL

 cause physical and property damage.

2) Indicates that the identified danger could 

POSSIBLY

 cause physical and property

damage.

3) Indicates a point of further interest or further explanation.

Software Warnings

4) Indicates special care must be taken when using this element of software.

5) Indicates a special point which the user of the associate software element should

be aware.

6) Indicates a point of interest or further explanation.

Summary of Contents for MELSEC FX2N-32DP-IF























































Reviews:

No comments