background image

NPN

Each output is set when the present value of the counter matches with the compare
value (which is transferred from the PC), and is switched OFF by a reset command
from the PC.

YH
YS
(Therefore, when the input frequency is 50 kHz, there is a worst case delay of 15 input
pulses.)

3

SPECIFICATIONS

3.1 Environmental specifications

The environmental specifications for the FX-1HC are the same as those for your FX series PC.

3.2 Performance specifications

t2

t2

t1

t1

t3

t3

t1 : Rise/fall time is 3

µ

s or less

t2 : ON/OFF pulse duration 10

µ

s or more

t3 : Phase difference between phase A and phase B

is 3.5

µ

s or more

PRESET (Z phase) input 100

µ

s or more

DISABLE (count prohibit) input 100

µ

s or more

Item

Input signal

Signal level

MAX. frequency

Pulse shape

Output

signal

Counting

specifi-

cation

Format

Range

Comparison Type

Output capacity

Automatic UP/DOWN (however, when on 1 phase 1 input mode, UP/DOWN is

determined by a PC command or an input terminal.)

When 32-bit is specified: -2,147,483,648 to +2,147,483,647

When 16-bit is specified: 0 to 65,535 (upper limit can be user specified)

DC 12V to 24V 0.5A

8 point taken from the FX, FX

2C

 expansion bus (can be either inputs or outputs)

DC 5V 70mA

+

Output

PNP

Output

I/O occupation

Power from base

YHN

YHP

YSN

YSP

: NPN transistor output for YH output

: PNP transistor output for YH output

: NPN transistor output for YH output

: PNP transistor output for YH output

: Direct output processed by hardware.
: Software processed output with worst delay time of 300

µ

s.

2-phase input

4 edge count

2 edge count

25 kHz

12.5 kHz

1 edge count

50 kHz

5V, 12V, or 24V ±10% (selected by terminal connection) 7mA

1 input

2 inputs

1-phase input

Types of outputs

Summary of Contents for MELSEC FX-1HC













Reviews: