manualshive.com logo in svg

Mitsubishi Electric MELDAS MDS-R Series, Specifications And Instruction Manual

Share
Download
Mitsubishi Electric MELDAS MDS-R Series Specifications And Instruction Manual Download Page 266

 

Appendix 1. Cable and Connector Specifications 

 

 
 

 

 

A1 - 25

 

(7)  Tightening angle back shell 

[1] Temporarily tighten the back shell coupling on the angle back shell. 

* To prevent loosening, Adhesive should be applied to the angle back shell. 

[2] Set the angle back shell on the tightening guide. 
[3] Set the back shell wrench on the back shell coupling. 
[4] With the wrench, tighten the back shell coupling on the angle back shell. 

Recommended tightening torque: 5N

m 

(Note)

 Accurately fit the wrench on the back shell coupling. 

To remove, take the reverse steps. 

 

 

* Recommendation 

Adhesive 

(2 threads around   

the circumference)

Temporary
tightening

 

 

Back shell 
coupling 

Tightening guide 

Set

Tightening guide

 

Torque wrench

Tighten 

Angle back shell 

wrench

19 

17 

* Referential dimensions for back

shell tightening guide 

Back shell width 

22 

Thickness: 
10 or more 

* Recommendation: 

Tightening guide 
(357J-50508T) 

 Recommended jigs and tools: Back shell wrench (357J-51333T) 

Bit (357J-51344T) 

Torque wrench (CL6N x 8D,Tonichi Mfg.) 

* Recommended tightening guide: (357J-50508T) 

* Recommended adhesive: screw lock 1401B (Threee bond Co,Ltd) 

Set

 

Angle back shell 

(Note) 

To change the back shell angle, adjust the toothing position of the plug shell
and back shell. 

 

Downloaded from 

ManualsNet.com

 search engine

Summary of Contents for MELDAS MDS-R Series











































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands