Mitsubishi Electric GT14, User Manual

Page: 604 / 1546

28 - 6
28. CNC CONNECTION
28.4 GOT Side Settings
(2) Ethernet (MELSEC), Q17nNC, CRnD-700
*1 Click the button and perform the setting in the [GOT
IP Address Setting] screen.
*2 Each of [GOT PLC No.] set in the communication detail
setting and [PLC No.] set in the Ethernet setting must be set
to different station numbers.
28.4.3 Ethernet setting
POINT POINT POINT
(1) Communication interface setting by Utility
The communication interface setting can be
changed on the Utility's [Communication setting]
after writing [Communication Settings] of project
data.
For details on the Utility, refer to the following
manual.
11. COMMUNICATION INTERFACE SETTING
(COMMUNICATION SETTING)
(2) Precedence in communication settings
When settings are made by GT Designer3 or the
Utility, the latest setting is effective.
28.4.3 Ethernet setting
*1 For operating CNC monitor function, set N/W No. to "239".
*2 Each of [GOT PLC No.] set in the communication detail
setting and [PLC No.] set in the Ethernet setting must be set
to different station numbers.
28.4.2 Communication detail settings
Item Description Range
GOT NET No.
Set the network No. of the GOT.
(Default: 1)
1 to 239
GOT PLC No.
*2
Set the station No. of the GOT.
(Default: 1)
1 to 64
GOT
IP Address
*1
Set the IP address of the GOT.
(Default: 192.168.3.18) 0.0.0.0 to
255.255.255.255
Subnet Mask
*1
Set the subnet mask for the sub
network. (Only for connection via
router)
If the sub network is not used, the
default value is set.
(Default: 255.255.255.0)
0.0.0.0 to
255.255.255.255
Default
Gateway
*1
Set the router address of the default
gateway where the GOT is
connected. (Only for connection via
router)
(Default: 0.0.0.0)
0.0.0.0 to
255.255.255.255
Ethernet
Download Port
No.
*1
Set the GOT port No. for Ethernet
download.
(Default: 5014)
1024 to 5010,
5014 to 65534
(Except for 5011,
5012, 5013, and
49153)
GOT
Communication
Port No. Set the GOT port No. for the
connection with the Ethernet module.
(Default: 5001)
1024 to 5010,
5014 to 65534
(Except for 5011,
5012, 5013, and
49153)
Retry
Set the number of retries to be
performed when a communication
timeout occurs.
When receiving no response after
retries, the communication times out.
(Default: 3times)
0 to 5times
Startup Time
Specify the time period from the GOT
startup until GOT starts the
communication with the PLC CPU.
(Default: 3sec)
3 to 255 sec
Timeout Time
Set the time period for a
communication to time out.
(Default: 3sec)
3 to 90sec
Delay Time
Set the delay time for reducing the
load of the network/destination PLC.
(Default: 0ms)
0 to 10000
( 10ms)
Item Description Range
Host
The host is displayed. (The host
is indicated with an asterisk (*).)
-
N/W No.
Set the network No. of the
connected Ethernet module.
(Default: blank)
Network No. of
CNC
*1
PLC No.
*2
Set the station No. of the
connected Ethernet module.
(Default: blank)
Station No. of CNC
Type
Set the type of the connected
Ethernet module.
(Default: QJ71E71)
AJ71QE71
IP Address
Set the IP address of the
connected Ethernet module.
(Default: blank)
IP address of CNC
Port No.
Set the port No. of the
connected Ethernet module.
(Default: 5001)
5001
Communication UDP (fixed) UDP (fixed)