Mitsubishi Electric FX2N-485-BD User Manual Download Page 49 | Manualshive

Page: 49 / 65

background image

7.5.3

Example of Set Program

For the set program for the master station and the stations Nos. 1 and 2, refer to Section 7.3.6 program.

Master station

Slave station No. 1

Slave station No. 2

Remarks

D8176

K0

K1

K2

Station No.

D8177

K2

Total slave station : 2 stastions

D8178

K1

Refresh range : Pattern 1

D8179

K3

Retry count : 3 times (default)

D8180

K5

comms time-out : 50 ms (default)

7

FX

2N

-485-BD COMMUNICATION BOARD

N:N NETWORK

7-12

«
...
47
48
49
50
51
...
»

Summary of Contents for FX2N-485-BD


































































Reviews:

No comments

Related manuals for FX2N-485-BD

Brand: U-Prox Pages: 31

Brand: Panasonic Pages: 72

Brand: Panasonic Pages: 45

Brand: Panasonic Pages: 24

Brand: IDK Pages: 96

Ecomot300 AC2630

Brand: IFM Electronic Pages: 111

Brand: RAKwireless Pages: 6

Brand: Watts Pages: 4

Brand: WaterCop Pages: 4

Brand: YASKAWA Pages: 49

Brand: M-system Pages: 17

Brand: hager Pages: 2

Brand: hager Pages: 4

Brand: Vizio Pages: 65

Brand: Vag Pages: 12

Brand: Fox Pages: 5

Brand: Jäger Pages: 18

Brand: Dantel Pages: 6

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands