Mitsubishi Electric FR-E800, Instruction Manual

Page: 275 / 484

274
12. (M) Item and Output Signal for Monitoring
12.2 Monitor item selection on operation panel or via communication
*11 The details of bits for the input terminal status are as follows. (1: ON state, 0: OFF state of a terminal on the inverter. "—" denotes an indefinite
(null) value.)
*12 The details of bits for the output terminal status are as follows. (1: ON state, 0: OFF state of a terminal on the inverter. "—" denotes an indefinite
(null) value.)
*13 The details of bits for the option input terminal status 1 are as follows. (1: ON state, 0: OFF state of a terminal on the FR-A8AX.) Every bit is 0
(OFF) when the option is not installed.
*14 The details of bits for the option input terminal status 2 are as follows. (1: ON state, 0: OFF state of a terminal on the FR-A8AX. "—" denotes an
indefinite (null) value.) Every bit is 0 (OFF) when the option is not installed.
*15 The details of bits for the option output terminal status are as follows. (1: ON state, 0: OFF state of a terminal on the FR-A8AY/A8AR. "—" denotes
an indefinite (null) value.) Every bit is 0 (OFF) when the option is not installed.
*16 The increment varies depending on the Pr.53 setting. (Refer to page 268 ).
*17 The monitored values are retained even if an inverter fault occurs. Resetting clears the retained values.
*18 Parameter setting is not valid to set the item as the main monitor item on the LCD operation panel (FR-LU08). Use the monitor function of the
FR-LU08 for the setting.

Monitor display for operation panel (Pr.52, Pr.774 to Pr.776)
• When Pr.52 = "0" (initial value), the monitoring of output frequency, output current, output voltage and fault display can be
selected in sequence by pressing the SET key.
• The Load meter, motor excitation current and motor load factor are displayed on the second monitor (output current)
position, among the monitors set in Pr.52 . Other monitors are displayed in the third monitor (output voltage) position.
• The monitor displayed at power ON is the first monitor (the output frequency monitor, according to the initial value). Display
the monitor you want to display on the first monitor and hold down the SET key for 1 second. To return to the output
frequency monitor, display the output frequency monitor and hold down the SET key for 1 second.
For example, when Pr.52 = "20" (cumulative energization time), the monitor is displayed on the operation panel as shown
below.
b15 Standard model b0
- - - - - - - - RES MRS RH RM RL STR STF -
b15 Ethernet model b0
- - - - - - - - - - - - - DI1 DI0 -
b15 Safety communication model b0
- - - - - - - - - - - - - - - -
b15 b0
- - - - - - - FU RUN -
b15 b0
- - - - - - - - -
- - -
- - - -
-
SO
SO
ABC
ABC
ABC
-
Standard model
Ethernet model
b15 Safety communication model b0
- - - - - - - - - - - - - - -
b15 b0
X11 X12 X13 X14 X10 X9 X8 X6 X7 X5 X4 X3 X2 X1 X0 X15
b15 b0
- - - - - - - - - - - - - - DY -
b15 b0
- - - - - RA3 RA2 Y6 RA1 Y5 Y4 Y3 Y2 Y1 Y0 -
Power-on monitor (first monitor) Second monitor Third monitor Fault monitor
With fault
Output current monitor
Output voltage monitor
Output frequency monitor
• Power-on monitor (first monitor) • Second monitor • Third monitor • Fault monitor
With fault
Output current monitor
Cumulative energization time monitor Output frequency monitor