Mitsubishi Electric FR-E800, Instruction Manual

Page: 274 / 484

11
12
13
14
15
16
17
18
19
20
273
12. (M) Item and Output Signal for Monitoring
12.2 Monitor item selection on operation panel or via communication
*1 The monitor code is used for the Mitsubishi inverter protocol, CC-Link, CC-Link IE TSN, and CC-Link IE Field Network Basic.
*2 The monitor code is used for the MODBUS RTU, MODBUS/TCP, and BACnet/IP.
*3 The monitor number is used for the EtherNet/IP and PROFINET.
*4 Indication with a minus sign is not possible via RS-485 communication (Mitsubishi inverter protocol or MODBUS RTU).
*5 To monitor the item on the LCD operation panel (FR-LU08) in the monitor mode, use Pr.774 to Pr.776 or the monitor function of the FR-LU08 for
setting.
*6 The cumulative energization time and actual operation time are accumulated from 0 to 65535 hours, then cleared, and accumulated again from 0.
*7 The actual operation time does not increase if the cumulative running time before power OFF is less than an hour.
*8 Since each readout of the output voltage and output current displayed on the operation panel is a 4-digit number, a value of more than "9999" is
displayed as "----".
*9 The inverter regards the output current which is less than the specified current level (5% of the rated inverter current) as 0 A. Therefore, each
readout of an output current and output power may show "0" if a too small-capacity motor is used as contrasted with the inverter capacity and the
output current falls below the specified value.
*10 Available when the plug-in option is connected.
Option input
terminal status 1
(for
communication)
*1
0
— —
H3A
*13
40258
*13
3A
The ON/OFF state of the input terminals X0 to
X15 on the digital input option (FR-A8AX) is
monitored via communication.
Option input
terminal status 2
(for
communication)
*1
0
— —
H3B
*14
40259
*14
3B
The ON/OFF state of the input terminal DY on
the digital input option (FR-A8AX) is monitored
via communication.
Option output
terminal status
(for
communication)
*1
0
— —
H3C
*15
40260
*15
3C
The ON/OFF state of the output terminals on the
digital output option (FR-A8AY) or the relay
output option (FR-A8AR) is monitored via
communication.
Motor thermal
load factor
0.1% 61 H3D 40261 3D
The accumulated heat value of the motor
thermal O/L relay is displayed.
The Motor overload trip (electronic thermal relay
function) (E.THM) occurs at 100%.
Inverter thermal
load factor
0.1% 62 H3E 40262 3E
The accumulated heat value of the inverter
thermal O/L relay is displayed.
The Inverter overload trip (electronic thermal
relay function) (E.THT) occurs at 100%.
PID measured
value 2
0.1% 67 H43 40267 43
The PID measured value is displayed while the
PID control is enabled (
Pr.128 ≠ "0"), even if PID
control operating conditions are not satisfied.
(Refer to
page 389 .)
32-bit cumulative
energy (lower 16
bits)
1 kWh — H4D 40277 4D
The upper or lower 16 bits of the 32-bit
cumulative energy is displayed on each
indication.
Monitoring via communication is available.
32-bit cumulative
energy (upper 16
bits)
1 kWh — H4E 40278 4E
32-bit cumulative
energy (lower 16
bits)
0.01 kWh — H4F 40279 4F
32-bit cumulative
energy (upper 16
bits)
0.01 kWh — H50 40280 50
BACnet valid
APDU counter
1 83 H53 40283 53
The count of valid APDU detection is displayed.
(Available only for the FR-E800-EPA and FR-
E800-SCEPA.)
PID manipulated
amount
0.1% 91 H5B 40291 5B ○
The PID control manipulated amount is
displayed. (Refer to
page 389 .)
Dancer main set
speed
0.01 Hz
*16
97 H61 40297 61
The set speed for main speed during the dancer
control operation is displayed.
Monitor item
Incremen
t and unit Pr.
setting
Communication
Negative
indicatio
n (-)
*4
Description
Monitor
code 1
*1
Monitor
code 2
*2
Monitor
number
*3