background image

1

1 PRODUCT CHECKING AND PARTS IDENTIFICATION

Unpack the inverter and check the capacity plate on the front cover and the rating plate on the inverter side face to ensure that
the product agrees with your order and the inverter is intact.

z

Installation of the inverter
Enclosure surface mounting
Remove the front cover and wiring cover to mount the inverter to the surface.

Note

y

When encasing multiple inverters, install them in parallel as a
cooling measure.

y

When using the inverters at the surrounding air temperature of 
40°C (104°F) or less, the inverters can be installed without any 
clearance between them (0cm (0 inches) clearance). When 
surrounding air temperature exceeds 40°C (104°F), clearances 
between the inverters should be 1cm (0.39inches) or more (5cm 
(1.96inches) or more for the FR-D720-238 and FR-D740-120 or 
higher).

y

Install the inverter vertically.

FR

D740

036

-

-

- NA

Symbol

Voltage class

D740

Three-phase 400V class

Rating plate

Inverter model

Input rating

Output rating

Serial number

FR-D740-036-NA

Inverter model

Rating plate

Represents 
the rated 
current

Inverter model Serial number

Capacity plate FR-D740-036-NA

D720S

Single-phase 200V class

D710W

Single-phase 100V class

D720

Three-phase 200V class

DATE:XXXX-XX

Production year and month

Front cover

Front cover

Wiring cover

Wiring cover

FR-D720-008 to 042 
FR-D720S-008 to 042
FR-D710W-008 to 025

FR-D720-070 or higher
FR-D740-012 or higher 
FR-D720S-070, 100
FR-D710W-042

10cm(3.94inches)
 or more

10cm(3.94inches)
 or more

V

e

rtical

Refer to the 

clearances

on the left.

Summary of Contents for FR-D710W-008































Reviews: