Mitsubishi Electric DX-TL4509E series, Installer Manual

Page: 109 / 128

Warnings and CALL OUT output
109
ENGLISH
Page
Warning Display
CALL OUT
output
#1
Cancelling
the warning
Log number Countermeasure
#
#
#
18
–
49-51,
91
–
–
78
–
–
–
–
–
41, 42
41, 42
–
LOG54 #7
LOG13 #8
LOG33 #8
LOG43 #8
LOG73 #8
LOG23 #8
LOG14 #8
LOG74 #8
LOG24 #8
LOG34 #8
LOG44 #8
LOG55 #7
LOG6200
LOG5100
LOG5200
LOG5201
LOG5300
LOG3500#5
LOG7500#6
LOG3600#5
LOG7600#6
LOG5101
LOG5102
LOG5103
Fixed
None
Fixed
None
None
Fixed
Fixed
Fixed
Fixed
Fixed
None
None
–
No Camera Signal
Camera signal is lost or distorted.
Please check the camera and cable
connection.
It can use as it is though a slight error
occurred.
System suspended due to unstable
processing. Recording will be resumed.
HDD was disconnected.
System suspended due to unstable
processing. Start operation again.
The recorder detected the data altered or data
recorded by other recorder.
Recorder detected technical problems
on the device.
The recorder has been rebooted. The problem
is not critical, but check the recorder.
Internal temperature is getting too high,
check the ventilation of the recorder.
Internal temperature is getting too high,
stop the operation of the recorder
immediately.
The fan of the recorder needs to be checked.
Copying data stopped because of new record
overwrites the old data.
New record will soon overwrite the old data
in copying.
Stop the recording, if you want to continue the
copying.
(NONE)
• Check whether the unit and
camera are properly connected
and turned on.
• Check whether the video signal is
being properly outputted.
• Check whether the camera with
no video signal input is set for
operation.
• Continue the operation when
there is no abnormality.
• When the error occurs
continuously, check the
HDD/media and cable and then
restart the unit.
• Restart the unit.
• Check the unit.
• Turn off the power and change
the installation condition.
• Turn off the power and change
the installation condition.
• Turn off the power and stop
using.
• Stop HDD recording to continue
copy/backup.
• Stop HDD recording to continue
copy/backup.
• Stop copy/backup to continue
HDD recording.
• Restarts by watchdog operation
or for self-recovery.
Stop
recording.
Output video
signals.
Click "Clear
Warning" or press
the E button.
Automatically
clears after 1
minute.
Click "Clear
Warning" or press
the E button.
Automatically
clears after 1
minute.
Click "Clear
Warning" or press
the E button.
Click "Clear
Warning" or press
the E button.
Click "Clear
Warning" or press
the E button.
Click "Clear
Warning" or press
the E button.
Click "Clear
Warning" or press
the E button.
Lower the
temperature.
Click "Clear
Warning" or press
the E button.
Rotate the fan.
Click "Clear
Warning" or press
the E button.
Click "Clear
Warning" or press
the E button.
Regarding LOG14 : Displays during recording. The system shuts down once and then resumes recording. (The error HDD is
automatically deleted from the recording device. The recording is continued until all the registered HDDs are used up.)
Regarding LOG24 to 74 : Displays during copying or playback. The playback or copy stops because the system shuts down.
Carry out playback or copy again.
Regarding LOG 54 : Displays during recording when the video signal is not existed for the camera being recorded for 2 seconds
or more. This warning may not be displayed for the recording of which recording time is less than 2 seconds.