manualshive.com logo in svg

Mitsubishi Electric City Multi PMFY-P100VBM-E, Installation Manual, Page: 9 / 10

Share
Download
Mitsubishi Electric City Multi PMFY-P100VBM-E Installation Manual Download Page 9

9

6. Test run (Fig. 6-1)

TIMER SET

PAR-20MAA

ON/OFF 

CENTRALLY CONTROLLED

ERROR CODE

CLOCK

ON

OFF

˚C

CHECK

CHECK MODE

FILTER

TEST RUN

FUNCTION

˚C

1Hr.

NOT AVAILABLE

STAND BY 
DEFROST

FILTER

CHECK TEST

TEMP.

2

BC

3

4

5

1

A

E

D

1

Press [TEST RUN] button twice 

→

 displaying [TEST RUN] on the screen.

2

Press [Selecting operation] button. 

→

 Check that wind is blowing out.

3

Press [Fan speed adjustment] button. 

→

 Check that the wind speed is changed.

4

Press [Up/down airflow selection] button to change wind direction.

5

Press [ON/OFF] button to clear test run

. →

 Test run stops.

A

Lighting in operation

B

Displaying inspection code

C

Displaying remaining test run time

D

Displaying indoor unit’s liquid pipe temperature

E

Displaying test run

Note:
• The 2-hour-set timer is activated to automatically stop test run after two hours.
• The remote controller displays the temperature of the indoor unit’s liquid

pipe on the temperature display section during test run.

Fig. 6-1

Summary of Contents for City Multi PMFY-P100VBM-E











Reviews:

No comments