15
en
5. Electrical work
■
Manual vane angle (Wired remote controller)
1
Select “Comfort” from the Operation
menu, and press the [SELECT]
button.
2
Select “Manual vane angle” with the
[F1] or [F2] button, and press the
[SELECT] button.
3
Select the “M-NET address” for the
units to whose vanes are to be fixed,
with the [F2] or [F3] button, and press
the [SELECT] button.
Press the [F4] button to confirm the
unit.
The vane of only the target indoor unit
is pointing downward.
4
Select “Vane” with the [F1] button.
Select “4-way” or “2-way” with the
[F2] or [F3] button, and press the [F4]
button.
5
The current vane setting will appear.
Select the desired outlets from 1
through 4 with the [F1] or [F2] button.
• Outlet: “1”, “2”, “3”, “4” and “1, 2, 3, 4,
(all outlets)”
Press the [F3] or [F4] button to go
through the option in the order of “No
setting (reset)”, “Step 1”, “Step 2”,
“Step 3”, “Step 4”, “Step 5” and “Draft
reduction*”.
Select the desired setting.
* Draft reduction
The airflow direction for this setting
is more horizontal than the airflow
direction for the “Step 1” setting in
order to reduce a drafty feeling. The
draft reduction can be set for only 1
vane.
■
Vane setting
No setting
Step 1
Step 2
Step 4
Step 3
All
outlets
Draft
reduction*
Step 5
Press the [SELECT] button to save the settings.
A screen will appear that indicates the setting information is being
transmitted.
The setting changes will be made to the selected outlet.
The screen will automatically return to the one shown above (step 5)
when the transmission is completed.
Make the settings for other outlets, following the same procedures.
If all outlets are selected,
will be displayed the next time the unit
goes into operation.
Navigating through the screens
• .To return to the previous screen ....................[RETURN] button
■
Confirmation procedure
1
Manual vane angle
Input display:
Address
Check
M-NET address
Identify unit Check button
F1
F2
F3
F4
Manual vane angle
Return:
M-NET address
Function setting for unit
with vane fully open.
F1
F2
F3
F4
Manual vane angle
Return:
No communication
Check Unit state.
F1
F2
F3
F4
Caution:
To prevent falls, maintain a stable footing when operating the unit.
1
Select the “M-NET address” for the
units to whose vanes are to be fixed,
with the [F2] or [F3] button. Press the
[F4] button to confirm the unit.
2
After pressing the [F4] button, wait
approximately 15 seconds, and then
check the current state of the air
conditioner.
→ The vane is pointing downward. →
This air conditioner is displayed on the
remote controller.
→ All outlets are closed. → Press the
[RETURN] button and continue the
operation from the beginning.
→ The messages shown to the left are
displayed. → The target device does
not exist at this refrigerant address.
• Press the [RETURN] button to return
to the initial screen.
3
Change the “M-NET address” to the
next number.
• Refer to
1
to change the “M-NET
address” and continue with the
confirmation.
Note:
Do not set the draft reduction in an environment with high humidity.
Otherwise, condensation may form and drip.
Main menu:
Cursor
Operation
Vane·Louver·Vent. (Lossnay)
High power
Comfort
F1
F2
F3
F4
Setting display:
Cursor
Comfort
Manual vane angle
3D i-See sensor
F1
F2
F3
F4
Manual vane angle
Input display:
Address
Check
M-NET address
Identify unit Check button
1
Manual vane angle
Manual vane angle
F1
F2
F3
F4
Select:
Setting
Outlet
Angle
Manual vane angle
Cur.
Angle
M-NET address
Vane
4-way
/2-way
Cursor
F1
F2
F3
F4
Input display:Angle button
F1
F2
F3
F4
F1
F2
F3
F4
BH79A523H02_01en.indd 15
2020/09/25 16:13:30
017
