background image

BC29

 

B

ATTERY 

C

ABINET

 

 
4/16/2014 

 

13 

755-00087 R03 

Wire Size and Type:

 Per NEC and/or all applicable national and local codes. 

 

6.4

 

G

ENERAL 

S

PECIFICATIONS

 

Cabinet Size:

 29.77”W x 29”D x 55.11”H 

Empty Cabinet Weight (approximately):

 175 lbs.

 

Operating  Temperature:

  20°C  to  25°C  (68°F  to  77°F)  recommended  for  optimum  battery 

performance. 

Ventilation:

  Through  ventilation  slots  front  and  rear.  A  minimum  of  four  inches  is  required  in 

front and behind the cabinet. This refers to obstruction of ventilation only. Clearance around the 
equipment should be as suggested by NEC and/or all applicable national and local codes. 

 

 

 

Wire should be sized for a maximum voltage drop of 0.5 volt. 

 

Under  certain  conditions,  batteries  can  vent  potentially  explosive  gas  (hydrogen). 
Never enclose batteries or battery cabinets in a sealed room. 

 

Batteries  should  be  stored  no  longer  than  three  months  at  25°C  (77°F)  or  lower 
before recharging. Exceeding the recommended ambient storage temperature may 
cause damage to the batteries. 

Summary of Contents for C&C Power BC29
























Reviews: