34 0.5(1.33)
50 1(1.96)
60
26.5(1.04)
18.3(0.72)
21
.3
(0.83)
68(2.68)
24(0.94)
25
(0.98)
200
+1 0
M4 mounting screw
19
2 1
4.3(0.17)
2-4.5 6 mounting screw
1)
6)
d
7)
Storage
sheet
6)
c
33(1.30)
+1
0
(2.36)
(7.87)
25
(0.98)
25(0.98)
(7.56)
A
J65FBTA42-16DTE
Y8
Y9
YA
YB
YC
YD
YE
YF
Y
Y
Y
Y
Y
Y
Y
Y
POWER
PROTECT
4.1(0.16)
35(1.37)
21.7(0.85)
32(1.26)
6(0.24)
48(1.89)
6(0.24)
Unit:mm(inch)
External connection
Communication connector
Pin
No.
LINK IN
LINK OUT
1 SLD SLD
2 DB
DB
3 DG
DG
4 DA
DA
5 No
pins Empty
Power connector
Pin
No.
UNIT
POWER
AUX.
1 +24V(UNIT)
+24V(I/O)
2 Empty Empty
3 24G(UNIT) 24G(I/O)
4 Empty Empty
5
(FG)
(FG)
I/O connector
Pin
No.
Signal
name
Pin
No.
Signal
name
1 +24V
1 Empty
2 X1
2
Y9
3 24G
3
24G
4 X0
4
Y8
X0
X1
5 Empty
Y8
Y9
5 Empty
1 +24V
1 Empty
2 X3
2
YB
3 24G
3
24G
4 X2
4
YA
X2
X3
5 Empty
YA
YB
5 Empty
1 +24V
1 Empty
2 X5
2
YD
3 24G
3
24G
4 X4
4
YC
X4
X5
5 Empty
YC
YD
5 Empty
1 +24V
1 Empty
2 X7
2
YF
3 24G
3
24G
4 X6
4
YE
X6
X7
5 Empty
YE
YF
5 Empty
Unit mounting screw
(FG)
I/O connector
Costant voltage
circuit
4-wire type sensor (source output)
110
130
Communication
circuit
Insulation
Terminal
resistance
select switch
3
5
4
4
1
LINK IN
2
3
4
1
2
3
5
LINK OUT
1
2
UNIT POWER
3
1
4
2
5
DC/DC
AUX.
3
4
1
2
5
3
4
1
2
5
3
4
1
2
5
L
L
3
4
1
2
5
Load power
Detection circuit
3-wire type sensor (source output)
2-wire type sensor (source output)
Black
Brown
Blue
White
Black
Brown
Blue
Brown
Blue
ON
ON
TERMINATION
110
130
40
10
4
1
2
20
8
2
4
1
STATION NO
B RATE
Communication adapter(back)
Communication adapter(front)
Connector for connection to main module
4)
5)
b
a
9)
Connector for connection
to communication adapter
10)
3)
8)
Communication
adapter
Main module
2)
1 2
2. Name and Setting of Each Area
No.
Item Description
LED name
Confirmation details
POWER
ON: Power supply ON OFF: Power supply OFF
PROTECT
Lights up when the output section protection function is
working (During the protect operation, fuse interruption is
searched in the master unit side)
L RUN
ON: Normal
communication
OFF: Communication shut off (time expiration error)
L ERR.
ON: Communication data error
Flash at regular intervals:
Indicates that the station number setting or
transmission speed setting switch position was
changed while power is ON
Flash at irregular intervals:
When the setting of the terminal resistor is wrong;
when the cable for the module or CC-Link is
affected by noise
OFF: Normal communication
1)
Operating
status indicator
LEDs
X0 to X7
Y8 to YF
ON: Input/Output
ON
OFF: Input/Output OFF
Setting switch status
Setting value
4 2 1
Transmission speed
0 OFF
OFF
OFF 156
kbps
1 OFF
OFF
ON 625
kbps
2 OFF
ON
OFF 2.5
Mbps
3 OFF
ON
ON 5.0
Mbps
4 ON
OFF
OFF 10
Mbps
2)
Transmission
speed setting
switch
Be sure to set the transmission speed within the above range.
Remove the communication adapter on the top part of the module to
set the transmission speed. (When shipped from the factory, all
settings are set to OFF.)
Select “10”, “20” or “40” to set the tens place of the station number.
Select “1”,”2”,”4” or “8” to set the ones place of the station number.
Always set the station number within the range of 1 to 64. (*1)
(Example) Set the switches as below when setting the station number
to 32:
Tens place
Ones place
Station
number
40 20 10 8 4 2 1
32
OFF ON ON OFF OFF
ON OFF
3) Station number
setting switch
Remove the communication adapter on the top part of the module to
set the station number. (When shipped from the factory, all settings
are set to OFF.)
The terminal resistor can be turned to the ON setting by using the
select switch.
DIP switch1 DIP switch2
Contents
OFF
OFF
No terminal resistance
ON OFF
110
Ω
resistor ON
OFF ON
130
Ω
resistor ON
ON ON
Setting
prohibited
4)
Terminal
resistance
setting switch
(When shipped from the factory, all settings are set to OFF.)
Silk
Contents
a LINK
IN
Connector for connecting the
transmission line from the IN side (master
station side). (Male 4 pins)
b LINK
OUT
Connector for connecting the
transmission line from the OUT side.
Be sure to attach the waterproof cap
when not in use. (Female 5 pins)
(Tightening torque range: 29 to 34 N.cm)
5)
Waterproof
connector for
transmission
line *2
Silk
Contents
c UNIT
POWER Connector for supplying power to the
module. (Male 5 pins)
d
AUX.
Connector for supplying power to a load,
etc. (Male 5 pins)
6)
Waterproof
connector for
power line *2
7)
Waterproof
connector for
input
connection *2
Waterproof connector for connection I/O signal. (Female 5 pins)
Be sure to attach waterproof cap A6CAP-WP2 (sold separately) when
not in use. (Tightening torque range: 29 to 34 N.cm)
8) FG metal fitting For module FG terminal (tightening torque range: 78 to 118 N.cm)
9)
Communication
adapter fixing
screw
When replacing the main body online or changing switch setting,
attach/remove the communication adapter with this screw.
(Tightening torque range: 42 to 58 N.cm)
10)
Module
attachment
hole
Screw hole for module attachment. 2-4.5 X 6 length hole
(M4 attachment screw) (Tightening torque range: 78 to 118 N.cm)
*1: Duplicate station number cannot be set.
*2: Waterproof connector (based on IEC947-5-2, M12 type)
