Mitel MiVoice Business 3300 ICP Troubleshooting Manual Download Page 12

Page: 12 / 366

Introduction

Note

Online Service Desk (OSD) response time is three business days. The OSD should

not be used to obtain emergency support services.

•

What Services are Available

on page 6

•

What Products are Supported

on page 7

•

Registering for Services

on page 8

1.3.1 What Services are Available

•

Mitel Knowledge Base:

provides access through the Mitel Online website to the

latest product information. The Knowledge base provides

•

Technical Bulletins (TBs)

: Provide information on the installation and service of Mitel

products. TBs are issued to introduce new software support tools, provide support

information on discontinued products, identify product issues and describe TSN

program policies.TBs are published when required.

•

How to Articles:

Provide information on proper programming of features and

applications

•

Troubleshooting Articles:

Provide troubleshooting procedures to help identify and

solve issues.

•

Known Product Issues:

Describe product issues that are known by Mitel and are in

the process of being resolved.

•

Release Notes (RNs):

Provide software upgrade procedures, describe

documentation and hardware requirements, summarize the new enhancements in

a release, identify improvements that have been made in the product in response

to customer reported issues, and include last-minute product changes that are not

described in the latest documentation. RNs are published for each new software

release.

•

Standard telephone support:

Allows certified channel partner technicians to consult

Mitel Network’s Technical Support Specialists on current products during normal

business hours. For details see

Making a Support Call

•

After-hours emergency telephone support:

Outside of normal business hours,

certified technicians can consult with a Technical Support Specialist or a Support

Manager for assistance with resolving an emergency situation or with restoring service

for an essential services site. See

What are After-Hours Calls?

for details.

•

Online Service Desk (OSD):

Allows you to view the status of your active Technical

Support Tickets and your technical credit statement. Whenever changes are submitted

against your account, you will be sent a confirmation email.To register for OSD

Document Version 1.0
Troubleshooting Guide

Summary of Contents for MiVoice Business 3300 ICP















































































































































































































































































































































































Search results

Summary of Contents for MiVoice Business 3300 ICP

Reviews:

Related manuals for MiVoice Business 3300 ICP

Brands by name

Popular brands

Mitel MiVoice Business 3300 ICP, Troubleshooting Manual

Search results

Summary of Contents for MiVoice Business 3300 ICP

Reviews:

Related manuals for MiVoice Business 3300 ICP

Brands by name

Popular brands