manualshive.com logo in svg

Mitel CPDM3, Installation Manual

Share
Download
Mitel CPDM3 Installation Manual Download Page 25

TD 

34/1531-ANF901 43 B1 2016-03-31

Installation Guide

22

Install the Port Driver on Windows 7

NOTE: When switching between mass storage mode and network mode, it takes about 

30 seconds before the product can be accessed with the 192.5.36.229 address.

1

Connect a mini-USB type B cable between the USB port on your computer and 
the management port on the product.

The Found new hardware wizard opens but at this stage there is no valid port 
driver so close the wizard and continue to install the driver.

2

Press the Mode button twice to change the mode to mass storage. 

The module will now turn up as a mass storage device on your computer. This is 
indicated by slow flashing blue light 

 on the Mode button LED. 

3

Locate the required “elise3.inf” driver and save it on your computer.

4

Press the Mode button twice again to change the mode to network access

1

.

5

Select Control Panel > Hardware and Sound.

6

Select “Device Manager” under Devices and Printers.

7

Right click “RNDIS/Ethernet gadget” and select “Update driver software”. A new 
window opens.

8

Click “Browse my computer for driver software”.

9

Browse to the folder where the port driver is saved and click “Next”. A Windows 
security window opens.

1.  If not pressed within 10 minutes the product will automatically change to Network access (default mode).

Summary of Contents for CPDM3





































Reviews:

No comments

Brands by name

Popular brands

Load more brands