background image

NOTICE

The information contained in this document is believed to be accurate in all respects but is not warranted 
by Mitel Networks™ Corporation (MITEL

®

). The information is subject to change without notice and should 

not be construed in any way as a commitment by Mitel or any of its affiliates or subsidiaries. Mitel and its 
affiliates and subsidiaries assume no responsibility for any errors or omissions in this document. Revisions 
of this document or new editions of it may be issued to incorporate such changes.

No part of this document can be reproduced or transmitted in any form or by any means - electronic or 
mechanical - for any purpose without written permission from Mitel Networks Corporation.

Trademarks

The trademarks, service marks, logos and graphics (collectively "Trademarks") appearing on Mitel's 
Internet sites or in its publications are registered and unregistered trademarks of Mitel Networks 
Corporation (MNC) or its subsidiaries (collectively "Mitel") or others. Use of the Trademarks is prohibited 
without the express consent from Mitel. Please contact our legal department at l

[email protected]

 for 

additional information. For a list of the worldwide Mitel Networks Corporation registered trademarks, please 
refer to the website: 

http://www.mitel.com/trademarks

.

Mitel 6800 Series Wall Mount Kit Installation Guide

41-001518-00 REV02 - November 2015

®,™ Trademark of Mitel Networks Corporation

© Copyright 2015, Mitel Networks Corporation

All rights reserved

Summary of Contents for 6800 Series






















Reviews: