voltage to your device. Press the power button twice in quick
succession to select the required voltage. Press the power
button this way until the display shows 12V, then connect the
black male end of the polarity reversal adapter to the 12V DC
power input on the Quad Cortex.
If the Quad Cortex does not power on. Check that you have
correctly connected the DC power cable and polarity reversal
adapter. Check that the display on the 529P show suffi cient
charge and indicates 12V on the DC output. YOU MUST SET
THE VOLTAGE TO 12V BEFORE CONNECTING THE DC
OUTPUT TO THE QUAD CORTEX. DO NOT ATTEMPT TO
POWER THE QUAD CORTEX AT ANY VOLTAGE OTHER
THAN 12V.
6. NeuralDSP Quad Cortex with additional pedals
The 529P can be used to power the Quad Cortex and a few
additional effects pedals. There are two options depending
on the type and number of additional pedals you need to
power.
Option 1 – Quad Cortex plus 4 pedals
This option powers the Quad Cortex PLUS 4 x 9V 150mA
pedals.
Connect the Quad Cortex to the 529P DC-OUT as described
in section 4. Connect a 529 (purchased separately) to one of
the USB A outputs as described in section 2. Note that the
150mA outputs will be isolated. The 500mA output on the
529 will not be isolated. It’s possible to use this output but
there may be an increase in noise depending on what device
is connected. For greater than 4 outputs and higher current
pedals it’s recommended to use option 2
Option 2 – Quad Cortex plus 8 pedals
This option powers the Quad Cortex PLUS 8 x 9V 500mA
pedals (16.8W maximum). This option requires the 529P plus
a 529M and 529X (both purchased separately). Connect the
529X to the DC-OUT as described in section 3. Then connect
the 529M to the TYPE-C output as described in section 4.
Select the 12V setting on the 529M and connect the output
of the 529M to the Quad Cortex power input.
7. Line 6 Pod, HX Stomp, and HX Effects
Connect the yellow end of the DC power cable to DC-OUT
on the 529P. The DC-OUT is center pin POSITIVE and the
Line 6 devices require 9V center NEGATIVE so you will need
to use the polarity reversal adapter. Connect the black end
of the DC cable to the red female end of the polarity reversal
adapter. The power input jack on the Line 6 device is 2.5mm
so you will need to use the 2.5mm adapter. Connect the
black male end of the polarity reversal adapter to the black
female end of the 2.5mm adapter.
Ensure that the power switch on your Line 6 device is switched
OFF. Connect the red male 2.5mm end of the adapter to the
9VDC power input. Press and hold the power button on the
529P until the display turns on. The output defaults to 5V. This
is to prevent accidentally providing excessive voltage to your
device. Press the power button twice in quick succession to
select the required voltage. Press the power button this way
until the display shows 9V, then turn the power switch on the
Line 6 device to ON.
If the device does not power on. Check that you have correctly
connected the DC power cable, polarity reversal adapter and
2.5mm adapter. Check that the display on the 529P shows
suffi cient charge and indicates 9V on the DC output.
8. Line 6 with additional pedals
The 529P can be used to power Line 6 Pod, HX Stomp or
HX Effects and a few additional effects pedals. There are two
options depending on the type and number of additional
pedals you need to power.
Option 1 – Line 6 plus 4 pedals
This option powers the Line 6 device PLUS 4 x 9V 150mA
pedals.
Connect the Line 6 device to the 529P DC-OUT as described
in section 7. Connect a 529 (purchased separately) to one
of the USB A outputs as described in section 2. Note that
in this confi guration the 500mA output on the 529 will not
be isolated from the Line 6 device. It’s possible to use this
output but there may be an increase in noise depending on
what device is connected. For greater than 4 outputs and
higher current pedals it’s recommended to use option 2
Option 2 – Line 6 plus 8 pedals
This option powers the Line 6 device PLUS 8 x 9V 500mA
pedals (16.8W maximum). This option requires the 529P plus
a 529M and 529X (both purchased separately). Connect the
529X to the DC-OUT as described in section 3. Then connect
the 529M to the TYPE-C output as described in section 4.
Select the 9V setting on the 529M and connect the output of
the 529M to the Line 6 power input.
9. Other devices
The 529P can be used to power or recharge many devices
such as laptop computers, smart devices, small audio
amplifi ers and desktop audio equipment that use USB or DC
power. A set of adapter cables and connectors are included.
Make sure to use the correct adapter, voltage and polarity
for the device.
Specifi cations
Battery type: Lithium polymer
Capacity: 25000mAh
DC input: 19V @ 2A
USB C PD Output: 5V/9V/12V 3A max
USB A Outputs: 5V 3A max
DC Output: 5V/8.4V/9V 3A max, 12V/16V/20V 4.5A max
Safety Instructions
Clean only with a dry cloth. Never use water, soap or
chemicals
Do not use near water
Do not drop, pierce or compress the enclosure
Do not use near any heat sources or in direct sunlight
Recharge once every three months if not used
Be careful to use the correct polarity and voltage for your
powered device
Mission Engin
ring Inc.
www.missionengineering.com [email protected] +1-866-333-1828
