background image

14

Mirka® DEOS 353X, 383X & Delta 663X • 110 V

en

Disposal information 

DANGER 
Disposal guidelines for old appliances . Render redundant power tools unusable by removing the 
power cord . Only for EU countries . Do not dispose of electric tools along with household waste . 
According to European Directives 2011/65/EU, 2015/863/EU and 2012/19/EU on waste electrical 
and electronic equipment and their implementation under national law, electric tools that have 
reached the end of their life must be collected separately and taken to an environmentally compatible 
recycling facility .

Troubleshooting guide

Symptom

Possible cause

Solution

The sander LED (right) is flashing 
between red and green.

Connected to a mains outlet with wrong 
voltage .

Connect the sander to a mains outlet that 
matches the nominal voltage of the tool .

No light from sander LED (right) when 
switched on.

Power cord not properly attached to the 
sander or to the mains socket .

Connect it properly .

The sander LED (right) is red and the 
sander slows down to 5,000 rpm when 
sanding.

Temperature too high in the sander . Too 
heavy long-term load .

Reduce the load on the sander for some 
time and the sander will speed up again .

The sander LED (right) is red and rpm is 
slightly reduced.

Too heavy short-term load .

Use lighter load and the LED (right) will 
automatically change to green .

The sander has stopped and LED (right) 
is red.

The tool is in safety mode due to high 
temperature .

Wait until the tool has cooled down .

Pad saver

Mirka’s pad savers are designed to protect the backing pad from wear and tear, when sanding aggressively and 
continuously with net products . These cost-effective pad savers, placed between the backing pad and the sanding 
strip, should be changed regularly . The pad savers prolong the life of the backing pad .

Further service 

Servicing must always be performed by trained personnel . To keep the tool warranty valid and ensure optimal tool 
safety and function, servicing must be carried out by a Mirka authorized service center . To locate your local Mirka 
authorized service center, contact Mirka Customer service or your Mirka dealer .

Learn more about 

power tools

 on our website.

Summary of Contents for DEOS 353
















Reviews: