manualshive.com logo in svg

Miranda ASD-231i, Installation And Operation Manual

Share
Download
Miranda ASD-231i Installation And Operation Manual Download Page 8

 

4 

 
1.  In order to remove the frame's front panel, gently pull on it. 
2.  Carefully place the ASD-231i between the module guides and gently push the module 

towards the rear of the frame until the module's edge connector is secured to the backplane.  
Pull lightly on the module verifying that it does not move. 

3.  Replace the frame's front panel. 

 
 
2.3   Rear Panel Label

 

 

Connector labels have been shipped with the ASD-231i.  These labels are to be installed on the 
frames’ rear panel in order to identify the module's external connectors. 
 

2.3.1   imaging Quartet Series/Solo Frames

 

 
To install the Quartet/Quartet-C/Quartet-M/Quartet-M-A75/Quartet-M-A110/Solo label, follow 
these steps while referring to Figure 2.1. 

 

1.  Remove the screws associated with the ASD-231i connectors. 
2.  Carefully apply the label to the connectors. 
3.  Replace the screws making sure not to damage the label. 

 
 

 

 

 

 

 

 

 

Figure 2.1

   Quartet/Solo rear panel label installation 

 

 
 

 

 

 

 

 

 

 

 
 

ASD-231i label

imaging 

Quartet, Quartet-C, Quartet-M,

 Quartet-M-A75, Quartet-M-A110,

or

imaging

 

Solo

(top view)

Summary of Contents for ASD-231i





























Reviews:

No comments

Brands by name

Popular brands

Load more brands