background image

Page 18

CAUTION

• It is normal for the heater to smoke during the first few minutes of use.

• If you smell gas – turn off the appliance and extinguish all flames. If the odour continues, immediately

contact your gas supplier.

• In the event of an uncontrollable fire, immediately disconnect the gas cylinder moving it away from fire 

and contact the fire services. DO NOT PUT YOURSELF AT RISK!

• Ensure aerosols are not used near this unit when in use.

• Ensure all packaging and plastic bags are disposed of safely.

 

Technical Data

Overall Height:    

 

 

86.6’’ approx.

Overall Weight: 

 

   82.6lbs

Overall Width:  

 

 

 

34’’

Heater Heat Input(·Qn):  

  38,200 

Btu/h

Heater Gas Consumption:  

 

2.0 Lbs per hour

Heater Injector Size:  

  0.07”

Setting Pressure:   

 

 

11” per W.C

Regulator Outlet Pressure:  

 

11” per W.C

Standard    

 

 

 

ANSI Z83.26a-2008 • CSA 2.37a-2008

 

 

 

 

 

 

Gas Fired Outdoor infrared Patio heaters

Gas Supply Pressure  

 

 

Max.250 PSI, MIN.5 PSI

Specifications are subject to change without prior notice.

Universal Innovations,

Kilcoole Ind. Est.,

Kilcoole,

Co. Wicklow,

Ireland.

Shall be used only in a well ventilated space and shall not be used in a building, 

garage or any other enclosed area. Maybe installed in shelter no more inclusive 

than:  – With walls on all sides but with no overhead cover.

          – Within a partial enclosure which includes an overhead cover and no more 

             than two side walls. These side walls may be parallel, as in a breezeway, 

             or at right angles to each other.

          – Within a partial enclosure which includes an overhead cover and three side 

             walls, as long as 30% or more of the horizontal periphery of the enclosure 

             is permanently open.

Warranty

Keep these instructions for future reference.The patio heater has been manufactured under the highest 

standards of quality and workmanship.We warrant to the original consumer purchaser that all aspects 

of this product will be free of defects in material and workmanship for 1 year from the date of purchase. 

A replacement for any defective part will be supplied free of charge for installation by the consumer. 

Defects or damage caused by the use of other genuine parts are not covered by this warranty. This 

warranty shall be effective from the date of purchase as shown in the purchaser’s receipt.

This warranty is valid for the original customer only and excludes product damage due to shipment 

or failure which results from alteration, product abuse or product misuse whether performed by a 

contractor, service company, or consumer.We will not be responsible for labor charges and/or damage 

incurred in installation, repair or replacement, nor for incidental or consequential damage.

Contact: [email protected] Tel: (678) 534 2876

40”(1M)

40”(1M)

Summary of Contents for 200 Btu




















Reviews: