www.mirabelleproducts.com
3
© 2013 Ferguson Enterprises, Inc. 18247 11/13
INSTALLATION
(FIG.3)
3. Now cut the countertop using the tem-
plate as a guide.
4. Mount the faucets and drain assembly
(not included) on your counter top, follow-
ing the faucet manufacturer’s instructions.
INSTALLATION
(FIG.3)
3. Tailler le comptoir en utilisant le gabarit
comme guide.
4. Monter le robinet et l’ensemble du drain
(non inclus) sur le comptoir en suivant les
instructions du fabricant du robinet.
INSTALACIÓN
(FIGURA3)
3. A continuación, cortar la cubierta usan-
do la plantilla como guía.
4. Montar el grifo y el ensamblaje del dre-
naje (no incluido) en la cubierta, siguiendo
las instrucciones del fabricante del grifo.
Cut-Out Ring
Model 9600
Tools and Supplies Needed for Installation
Installation Instructions
Self-Rim Lavatory
L. Drill
K. Sabre Saw
I. Hacksaw
J. Basin Wrench
H. Pipe Wrench
G. Putty Knife
F. Silicone Caulk
E. Tube Cutter
D. Tape Measure
B. Pliers
C. Adjustable Wrench
A. Regular and Phillip
Screwdriver
RIM LINE
TEMPLATE
CUTOUT LINE
Front
16-1/4” x 13-1/4”
(412mm x 336mm)
Important Installation Notes;
1. These instructions are for typical installations and if your situation is not representative to these instructions, you should consult a
professional.
2. If replacing an existing lavatory be certain to shut off water supply before removing old lavatory.
3. Be sure thatthe counter-top and space under the surface is large enough to accommodate the lavatory and drain assembly.
4. Do to slight variances in the manufacture process itis rec ommended thatthis template is used as a guideline along with the actual fixture
before any counter top is cut. The fixture dimensions should be compared to the template before cutting.
5. Position the lavatory upside down on the counter top making sure the productfits the dimensional limits ofthe surface and vanity.
6. Provide extra supportto the vanity if required by using 2x 4 braces on both sides ofthe sink opening. Attach with screws into the cabinet
framing. Angle brackets with screws shorter than the top and vanity wall thickness can be used to anchor the vanity top to the inside walls of
the vanity. (Angle brackets and screws notfurnished.)
(Caution; Broken vitreous china pieces are sharp and will cause severe cuts, use caution any time handling vitreous china products. Always take
precautions by using proper safety and sanitary protective wear.)
Installation Steps;
1. Mark the centerline ofthe counter top, if center location is desired as well as the centerline ofthe lavatory on the und erside ofthe lavatory.
Turn the lavatory over. Place it on the counter top with the two marks lined up. Trace around the perimeter ofthe lavatory. NOTE: THIS IS
NOT THE CUT OUT LINE; IT IS THE “OUTER BASIN RIM SHAPE”. (See Diagram 1)
2. Using scissors cutthe template outthatis your model numb er and align it with the tracing on the countertop, lay the template inside ofthe line
scribed on the counter-top in step 1. making sure thatthe edg es ofthe template are of equal distance from the lavatory tra ced rim line, tape
and mark the template location. (See Diagram 2)
3. Now cutthe countertop using the template as a guide.
4. Mountthe faucets and drain assembly (notincluded) on you r counter top, following the faucet manufacturer's instructions. (See Diagram 3)
5. Temporarily setthe lavatory into the cut out, check for al ignment and mark the desired location ofthe sink to help guid e you on the final
installation. (See Diagram 4)
6. Remove the lavatory after checking fit and alignment, turn lavatory upside down and apply a generous portion of sealant around the underside
ofthe rim near the edge. (See Diag
ram 5)
7. Center the bowl over the cutout and slowly lower the lavatory into place, align with the marks made earlier, then press down firmly.
8. Allow sealantto set before connecting supplies and drain .
9. Connect supply line to faucet and supply shut-off valves. Tighten connections atfaucet and shut-off valves for water tight seal. Connecttrap to
drain assembly, first hand tightto check alignmentthen sec ure joints for watertight assembly. (See Diagram 6)
10. CHECK FOR LEAKS!
Limited Warranty
Whatis the Warranty Period?
The warranty is for one year from installation date or purchase of home.
Who Is Covered?
The warranty covers the original purchaser or first home own
er.
What Does the Warranty Cover?
The warranty covers the vitreous china product that is defec
tive in materials or workmanship.
We will repair or replace the product with a replacement mode
l.
What Does the Warranty Not Cover?
Failures to fittings due to chlorine or other chemicals.
Installation and labor costs you incurred.
Repair costs and damage due to leaks from supply line failure
s.
Products not installed per Keller’s instructions.
Product that were subject to abuse or misuse.
Products that do not meet local building code requirements.
Products with faulty maintenance.
What do you do to get Service?
You may contact the place of purchase or call 561-630-0457
.
Tynan Plumbing Fixtures
PO Box 33178
Palm Beach Gardens, FL 33420
Maintenance and Care
Do not use abrasive powder or liquid cleaners which can damage the product surface.
Caution: Productis Fragile. To avoid breakage and possible injury handle with care!
REV 08/2013
INSTALLATION
(FIG.4)
5. Temporarily set the lavatory into the
cut out, check for alignment and mark the
desired location of the sink to help guide
you on the final installation.
INSTALLATION
(FIG. 4)
5. Placer temporairement le lavabo dans
la partie découpée, vérifier l’alignement et
marquer l’emplacement désiré du lavabo
comme guide pour l’installation finale.
INSTALACIÓN
(FIGURA 4)
5. Colocar el lavabo temporalmente en el
corte, revisando su alineación, y marcar la
ubicación deseada del lavabo que le ser-
virá como guía durante la instalación final.
Cut-Out Ring
Model 9600
Tools and Supplies Needed for Installation
Installation Instructions
Self-Rim Lavatory
L. Drill
K. Sabre Saw
I. Hacksaw
J. Basin Wrench
H. Pipe Wrench
G. Putty Knife
F. Silicone Caulk
E. Tube Cutter
D. Tape Measure
B. Pliers
C. Adjustable Wrench
A. Regular and Phillip
Screwdriver
RIM LINE
TEMPLATE
CUTOUT LINE
Front
16-1/4” x 13-1/4”
(412mm x 336mm)
Important Installation Notes;
1. These instructions are for typical installations and if your situation is not representative to these instructions, you should consult a
professional.
2. If replacing an existing lavatory be certain to shut off water supply before removing old lavatory.
3. Be sure thatthe counter-top and space under the surface is large enough to accommodate the lavatory and drain assembly.
4. Do to slight variances in the manufacture process itis rec ommended thatthis template is used as a guideline along with the actual fixture
before any counter top is cut. The fixture dimensions should be compared to the template before cutting.
5. Position the lavatory upside down on the counter top making sure the productfits the dimensional limits ofthe surface and vanity.
6. Provide extra supportto the vanity if required by using 2x 4 braces on both sides ofthe sink opening. Attach with screws into the cabinet
framing. Angle brackets with screws shorter than the top and vanity wall thickness can be used to anchor the vanity top to the inside walls of
the vanity. (Angle brackets and screws notfurnished.)
(Caution; Broken vitreous china pieces are sharp and will cause severe cuts, use caution any time handling vitreous china products. Always take
precautions by using proper safety and sanitary protective wear.)
Installation Steps;
1. Mark the centerline ofthe counter top, if center location is desired as well as the centerline ofthe lavatory on the und erside ofthe lavatory.
Turn the lavatory over. Place it on the counter top with the two marks lined up. Trace around the perimeter ofthe lavatory. NOTE: THIS IS
NOT THE CUT OUT LINE; IT IS THE “OUTER BASIN RIM SHAPE”. (See Diagram 1)
2. Using scissors cutthe template outthatis your model numb er and align it with the tracing on the countertop, lay the template inside ofthe line
scribed on the counter-top in step 1. making sure thatthe edg es ofthe template are of equal distance from the lavatory tra ced rim line, tape
and mark the template location. (See Diagram 2)
3. Now cutthe countertop using the template as a guide.
4. Mountthe faucets and drain assembly (notincluded) on you r counter top, following the faucet manufacturer's instructions. (See Diagram 3)
5. Temporarily setthe lavatory into the cut out, check for al ignment and mark the desired location ofthe sink to help guid e you on the final
installation. (See Diagram 4)
6. Remove the lavatory after checking fit and alignment, turn lavatory upside down and apply a generous portion of sealant around the underside
ofthe rim near the edge. (See Diag
ram 5)
7. Center the bowl over the cutout and slowly lower the lavatory into place, align with the marks made earlier, then press down firmly.
8. Allow sealantto set before connecting supplies and drain .
9. Connect supply line to faucet and supply shut-off valves. Tighten connections atfaucet and shut-off valves for water tight seal. Connecttrap to
drain assembly, first hand tightto check alignmentthen sec ure joints for watertight assembly. (See Diagram 6)
10. CHECK FOR LEAKS!
Limited Warranty
Whatis the Warranty Period?
The warranty is for one year from installation date or purchase of home.
Who Is Covered?
The warranty covers the original purchaser or first home own
er.
What Does the Warranty Cover?
The warranty covers the vitreous china product that is defec
tive in materials or workmanship.
We will repair or replace the product with a replacement mode
l.
What Does the Warranty Not Cover?
Failures to fittings due to chlorine or other chemicals.
Installation and labor costs you incurred.
Repair costs and damage due to leaks from supply line failure
s.
Products not installed per Keller’s instructions.
Product that were subject to abuse or misuse.
Products that do not meet local building code requirements.
Products with faulty maintenance.
What do you do to get Service?
You may contact the place of purchase or call 561-630-0457
.
Tynan Plumbing Fixtures
PO Box 33178
Palm Beach Gardens, FL 33420
Maintenance and Care
Do not use abrasive powder or liquid cleaners which can damage the product surface.
Caution: Productis Fragile. To avoid breakage and possible injury handle with care!
REV 08/2013
(FIG.3)
(FIG.4)
