www.mirabelleproducts.com
2
© 2013 Ferguson Enterprises, Inc. 18247 11/13
Recommended Tools and Materials
Outils et matériaux recommandés / Herramientas y materiales recomendados
Cut-Out Ring
Model 9600
Tools and Supplies Needed for Installation
Installation Instructions
Self-Rim Lavatory
L. Drill
K. Sabre Saw
I. Hacksaw
J. Basin Wrench
H. Pipe Wrench
G. Putty Knife
F. Silicone Caulk
E. Tube Cutter
D. Tape Measure
B. Pliers
C. Adjustable Wrench
A. Regular and Phillip
Screwdriver
RIM LINE
TEMPLATE
CUTOUT LINE
Front
16-1/4” x 13-1/4”
(412mm x 336mm)
Important Installation Notes;
1. These instructions are for typical installations and if your situation is not representative to these instructions, you should consult a
professional.
2. If replacing an existing lavatory be certain to shut off water supply before removing old lavatory.
3. Be sure thatthe counter-top and space under the surface is large enough to accommodate the lavatory and drain assembly.
4. Do to slight variances in the manufacture process itis rec ommended thatthis template is used as a guideline along with the actual fixture
before any counter top is cut. The fixture dimensions should be compared to the template before cutting.
5. Position the lavatory upside down on the counter top making sure the productfits the dimensional limits ofthe surface and vanity.
6. Provide extra supportto the vanity if required by using 2x 4 braces on both sides ofthe sink opening. Attach with screws into the cabinet
framing. Angle brackets with screws shorter than the top and vanity wall thickness can be used to anchor the vanity top to the inside walls of
the vanity. (Angle brackets and screws notfurnished.)
(Caution; Broken vitreous china pieces are sharp and will cause severe cuts, use caution any time handling vitreous china products. Always take
precautions by using proper safety and sanitary protective wear.)
Installation Steps;
1. Mark the centerline ofthe counter top, if center location is desired as well as the centerline ofthe lavatory on the und erside ofthe lavatory.
Turn the lavatory over. Place it on the counter top with the two marks lined up. Trace around the perimeter ofthe lavatory. NOTE: THIS IS
NOT THE CUT OUT LINE; IT IS THE “OUTER BASIN RIM SHAPE”. (See Diagram 1)
2. Using scissors cutthe template outthatis your model numb er and align it with the tracing on the countertop, lay the template inside ofthe line
scribed on the counter-top in step 1. making sure thatthe edg es ofthe template are of equal distance from the lavatory tra ced rim line, tape
and mark the template location. (See Diagram 2)
3. Now cutthe countertop using the template as a guide.
4. Mountthe faucets and drain assembly (notincluded) on you r counter top, following the faucet manufacturer's instructions. (See Diagram 3)
5. Temporarily setthe lavatory into the cut out, check for al ignment and mark the desired location ofthe sink to help guid e you on the final
installation. (See Diagram 4)
6. Remove the lavatory after checking fit and alignment, turn lavatory upside down and apply a generous portion of sealant around the underside
ofthe rim near the edge. (See Diag
ram 5)
7. Center the bowl over the cutout and slowly lower the lavatory into place, align with the marks made earlier, then press down firmly.
8. Allow sealantto set before connecting supplies and drain .
9. Connect supply line to faucet and supply shut-off valves. Tighten connections atfaucet and shut-off valves for water tight seal. Connecttrap to
drain assembly, first hand tightto check alignmentthen sec ure joints for watertight assembly. (See Diagram 6)
10. CHECK FOR LEAKS!
Limited Warranty
Whatis the Warranty Period?
The warranty is for one year from installation date or purchase of home.
Who Is Covered?
The warranty covers the original purchaser or first home own
er.
What Does the Warranty Cover?
The warranty covers the vitreous china product that is defec
tive in materials or workmanship.
We will repair or replace the product with a replacement mode
l.
What Does the Warranty Not Cover?
Failures to fittings due to chlorine or other chemicals.
Installation and labor costs you incurred.
Repair costs and damage due to leaks from supply line failure
s.
Products not installed per Keller’s instructions.
Product that were subject to abuse or misuse.
Products that do not meet local building code requirements.
Products with faulty maintenance.
What do you do to get Service?
You may contact the place of purchase or call 561-630-0457
.
Tynan Plumbing Fixtures
PO Box 33178
Palm Beach Gardens, FL 33420
Maintenance and Care
Do not use abrasive powder or liquid cleaners which can damage the product surface.
Caution: Productis Fragile. To avoid breakage and possible injury handle with care!
REV 08/2013
(A) Regular Screwdriver/Phillips Screwdriver (B) Pliers (C) Adjustable Wrench (D) Tape Measure (E) Tube Cutter
(F) Silicone Caulk (G) Putty Knife (H) Pipe Wrench (I) Hacksaw (J) Basin Wrench (K) Sabre Saw (L) Drill
(A) Tournevis régulier/tournevis cruciforme (B) Pinces (C) Clé ajustable (D) Ruban à mesurer (E) Coupe-tube
(F) Matériau d’étanchéité à base de silicone (G) Couteau à mastiquer (H) Clé à tube (I) Scie à métaux (J) Clé à robinet de montée
(K) Scie sauteuse (L) Perceuse
(A) Desarmador normal y Phillips (B) Alicates (C) Llave inglesa (D) Cinta métrica (E) Cortador de tubo
(F) Hule de silicón (G) Espátula para masilla (H) Llave para tubos (I) Sierra para metales (J) Llave para lavabo (K) Sierra sable (L) Taladro.
INSTALLATION
(FIG.1)
1. Mark the centerline of the counter top,
if center location is desired as well as the
centerline of the lavatory on the underside
of the lavatory. Turn the lavatory over. Place
it on the counter top with the two marks
lined up. Trace around the perimeter of
the lavatory. NOTE: THIS IS NOT THE
CUT OUT LINE; IT IS THE “OUTER BASIN
RIMSHAPE.”
INSTALLATION
(FIG.1)
1. Marquer la ligne centrale du comptoir si un
emplacement central est souhaité de même
que la ligne centrale du lavabo sur le dessus du
lavabo. Mettre le lavabo à l’envers. Le placer sur
le comptoir en alignant les deux repères. Tracer
le périmètre du lavabo. REMARQUE : IL NE
S’AGIT PAS DE LA LIGNE DE COUPE; IL S’AGIT
DE LA FORME DU « REBORD EXTÉRIEUR DE
LA CUVETTE. »
INSTALACIÓN
(FIGURA1)
1. Marcar la línea central de la cubierta, si
desea ubicarlo en el centro y en la línea
central del lavabo en la parte inferior del
lavabo. Voltear el lavabo. Colocarlo sobre
la cubierta alineando las dos marcas.
Trazar alrededor del perímetro del lavabo.
NOTA: ESTA NO ES LA LÍNEA DE CORTE.
ES LA FORMA DEL BORDE EXTERIOR
DEL LAVABO”.
Cut-Out Ring
Model 9600
Tools and Supplies Needed for Installation
Installation Instructions
Self-Rim Lavatory
L. Drill
K. Sabre Saw
I. Hacksaw
J. Basin Wrench
H. Pipe Wrench
G. Putty Knife
F. Silicone Caulk
E. Tube Cutter
D. Tape Measure
B. Pliers
C. Adjustable Wrench
A. Regular and Phillip
Screwdriver
RIM LINE
TEMPLATE
CUTOUT LINE
Front
16-1/4” x 13-1/4”
(412mm x 336mm)
Important Installation Notes;
1. These instructions are for typical installations and if your situation is not representative to these instructions, you should consult a
professional.
2. If replacing an existing lavatory be certain to shut off water supply before removing old lavatory.
3. Be sure thatthe counter-top and space under the surface is large enough to accommodate the lavatory and drain assembly.
4. Do to slight variances in the manufacture process itis rec ommended thatthis template is used as a guideline along with the actual fixture
before any counter top is cut. The fixture dimensions should be compared to the template before cutting.
5. Position the lavatory upside down on the counter top making sure the productfits the dimensional limits ofthe surface and vanity.
6. Provide extra supportto the vanity if required by using 2x 4 braces on both sides ofthe sink opening. Attach with screws into the cabinet
framing. Angle brackets with screws shorter than the top and vanity wall thickness can be used to anchor the vanity top to the inside walls of
the vanity. (Angle brackets and screws notfurnished.)
(Caution; Broken vitreous china pieces are sharp and will cause severe cuts, use caution any time handling vitreous china products. Always take
precautions by using proper safety and sanitary protective wear.)
Installation Steps;
1. Mark the centerline ofthe counter top, if center location is desired as well as the centerline ofthe lavatory on the und erside ofthe lavatory.
Turn the lavatory over. Place it on the counter top with the two marks lined up. Trace around the perimeter ofthe lavatory. NOTE: THIS IS
NOT THE CUT OUT LINE; IT IS THE “OUTER BASIN RIM SHAPE”. (See Diagram 1)
2. Using scissors cutthe template outthatis your model numb er and align it with the tracing on the countertop, lay the template inside ofthe line
scribed on the counter-top in step 1. making sure thatthe edg es ofthe template are of equal distance from the lavatory tra ced rim line, tape
and mark the template location. (See Diagram 2)
3. Now cutthe countertop using the template as a guide.
4. Mountthe faucets and drain assembly (notincluded) on you r counter top, following the faucet manufacturer's instructions. (See Diagram 3)
5. Temporarily setthe lavatory into the cut out, check for al ignment and mark the desired location ofthe sink to help guid e you on the final
installation. (See Diagram 4)
6. Remove the lavatory after checking fit and alignment, turn lavatory upside down and apply a generous portion of sealant around the underside
ofthe rim near the edge. (See Diag
ram 5)
7. Center the bowl over the cutout and slowly lower the lavatory into place, align with the marks made earlier, then press down firmly.
8. Allow sealantto set before connecting supplies and drain .
9. Connect supply line to faucet and supply shut-off valves. Tighten connections atfaucet and shut-off valves for water tight seal. Connecttrap to
drain assembly, first hand tightto check alignmentthen sec ure joints for watertight assembly. (See Diagram 6)
10. CHECK FOR LEAKS!
Limited Warranty
Whatis the Warranty Period?
The warranty is for one year from installation date or purchase of home.
Who Is Covered?
The warranty covers the original purchaser or first home own
er.
What Does the Warranty Cover?
The warranty covers the vitreous china product that is defec
tive in materials or workmanship.
We will repair or replace the product with a replacement mode
l.
What Does the Warranty Not Cover?
Failures to fittings due to chlorine or other chemicals.
Installation and labor costs you incurred.
Repair costs and damage due to leaks from supply line failure
s.
Products not installed per Keller’s instructions.
Product that were subject to abuse or misuse.
Products that do not meet local building code requirements.
Products with faulty maintenance.
What do you do to get Service?
You may contact the place of purchase or call 561-630-0457
.
Tynan Plumbing Fixtures
PO Box 33178
Palm Beach Gardens, FL 33420
Maintenance and Care
Do not use abrasive powder or liquid cleaners which can damage the product surface.
Caution: Productis Fragile. To avoid breakage and possible injury handle with care!
REV 08/2013
Cut-Out Ring
Model 9600
Tools and Supplies Needed for Installation
Installation Instructions
Self-Rim Lavatory
L. Drill
K. Sabre Saw
I. Hacksaw
J. Basin Wrench
H. Pipe Wrench
G. Putty Knife
F. Silicone Caulk
E. Tube Cutter
D. Tape Measure
B. Pliers
C. Adjustable Wrench
A. Regular and Phillip
Screwdriver
RIM LINE
TEMPLATE
CUTOUT LINE
Front
16-1/4” x 13-1/4”
(412mm x 336mm)
Important Installation Notes;
1. These instructions are for typical installations and if your situation is not representative to these instructions, you should consult a
professional.
2. If replacing an existing lavatory be certain to shut off water supply before removing old lavatory.
3. Be sure thatthe counter-top and space under the surface is large enough to accommodate the lavatory and drain assembly.
4. Do to slight variances in the manufacture process itis rec ommended thatthis template is used as a guideline along with the actual fixture
before any counter top is cut. The fixture dimensions should be compared to the template before cutting.
5. Position the lavatory upside down on the counter top making sure the productfits the dimensional limits ofthe surface and vanity.
6. Provide extra supportto the vanity if required by using 2x 4 braces on both sides ofthe sink opening. Attach with screws into the cabinet
framing. Angle brackets with screws shorter than the top and vanity wall thickness can be used to anchor the vanity top to the inside walls of
the vanity. (Angle brackets and screws notfurnished.)
(Caution; Broken vitreous china pieces are sharp and will cause severe cuts, use caution any time handling vitreous china products. Always take
precautions by using proper safety and sanitary protective wear.)
Installation Steps;
1. Mark the centerline ofthe counter top, if center location is desired as well as the centerline ofthe lavatory on the und erside ofthe lavatory.
Turn the lavatory over. Place it on the counter top with the two marks lined up. Trace around the perimeter ofthe lavatory. NOTE: THIS IS
NOT THE CUT OUT LINE; IT IS THE “OUTER BASIN RIM SHAPE”. (See Diagram 1)
2. Using scissors cutthe template outthatis your model numb er and align it with the tracing on the countertop, lay the template inside ofthe line
scribed on the counter-top in step 1. making sure thatthe edg es ofthe template are of equal distance from the lavatory tra ced rim line, tape
and mark the template location. (See Diagram 2)
3. Now cutthe countertop using the template as a guide.
4. Mountthe faucets and drain assembly (notincluded) on you r counter top, following the faucet manufacturer's instructions. (See Diagram 3)
5. Temporarily setthe lavatory into the cut out, check for al ignment and mark the desired location ofthe sink to help guid e you on the final
installation. (See Diagram 4)
6. Remove the lavatory after checking fit and alignment, turn lavatory upside down and apply a generous portion of sealant around the underside
ofthe rim near the edge. (See Diag
ram 5)
7. Center the bowl over the cutout and slowly lower the lavatory into place, align with the marks made earlier, then press down firmly.
8. Allow sealantto set before connecting supplies and drain .
9. Connect supply line to faucet and supply shut-off valves. Tighten connections atfaucet and shut-off valves for water tight seal. Connecttrap to
drain assembly, first hand tightto check alignmentthen sec ure joints for watertight assembly. (See Diagram 6)
10. CHECK FOR LEAKS!
Limited Warranty
Whatis the Warranty Period?
The warranty is for one year from installation date or purchase of home.
Who Is Covered?
The warranty covers the original purchaser or first home own
er.
What Does the Warranty Cover?
The warranty covers the vitreous china product that is defec
tive in materials or workmanship.
We will repair or replace the product with a replacement mode
l.
What Does the Warranty Not Cover?
Failures to fittings due to chlorine or other chemicals.
Installation and labor costs you incurred.
Repair costs and damage due to leaks from supply line failure
s.
Products not installed per Keller’s instructions.
Product that were subject to abuse or misuse.
Products that do not meet local building code requirements.
Products with faulty maintenance.
What do you do to get Service?
You may contact the place of purchase or call 561-630-0457
.
Tynan Plumbing Fixtures
PO Box 33178
Palm Beach Gardens, FL 33420
Maintenance and Care
Do not use abrasive powder or liquid cleaners which can damage the product surface.
Caution: Productis Fragile. To avoid breakage and possible injury handle with care!
REV 08/2013
Cut-Out Ring
Model 9600
Tools and Supplies Needed for Installation
Installation Instructions
Self-Rim Lavatory
L. Drill
K. Sabre Saw
I. Hacksaw
J. Basin Wrench
H. Pipe Wrench
G. Putty Knife
F. Silicone Caulk
E. Tube Cutter
D. Tape Measure
B. Pliers
C. Adjustable Wrench
A. Regular and Phillip
Screwdriver
RIM LINE
TEMPLATE
CUTOUT LINE
Front
16-1/4” x 13-1/4”
(412mm x 336mm)
Important Installation Notes;
1. These instructions are for typical installations and if your situation is not representative to these instructions, you should consult a
professional.
2. If replacing an existing lavatory be certain to shut off water supply before removing old lavatory.
3. Be sure thatthe counter-top and space under the surface is large enough to accommodate the lavatory and drain assembly.
4. Do to slight variances in the manufacture process itis rec ommended thatthis template is used as a guideline along with the actual fixture
before any counter top is cut. The fixture dimensions should be compared to the template before cutting.
5. Position the lavatory upside down on the counter top making sure the productfits the dimensional limits ofthe surface and vanity.
6. Provide extra supportto the vanity if required by using 2x 4 braces on both sides ofthe sink opening. Attach with screws into the cabinet
framing. Angle brackets with screws shorter than the top and vanity wall thickness can be used to anchor the vanity top to the inside walls of
the vanity. (Angle brackets and screws notfurnished.)
(Caution; Broken vitreous china pieces are sharp and will cause severe cuts, use caution any time handling vitreous china products. Always take
precautions by using proper safety and sanitary protective wear.)
Installation Steps;
1. Mark the centerline ofthe counter top, if center location is desired as well as the centerline ofthe lavatory on the und erside ofthe lavatory.
Turn the lavatory over. Place it on the counter top with the two marks lined up. Trace around the perimeter ofthe lavatory. NOTE: THIS IS
NOT THE CUT OUT LINE; IT IS THE “OUTER BASIN RIM SHAPE”. (See Diagram 1)
2. Using scissors cutthe template outthatis your model numb er and align it with the tracing on the countertop, lay the template inside ofthe line
scribed on the counter-top in step 1. making sure thatthe edg es ofthe template are of equal distance from the lavatory tra ced rim line, tape
and mark the template location. (See Diagram 2)
3. Now cutthe countertop using the template as a guide.
4. Mountthe faucets and drain assembly (notincluded) on you r counter top, following the faucet manufacturer's instructions. (See Diagram 3)
5. Temporarily setthe lavatory into the cut out, check for al ignment and mark the desired location ofthe sink to help guid e you on the final
installation. (See Diagram 4)
6. Remove the lavatory after checking fit and alignment, turn lavatory upside down and apply a generous portion of sealant around the underside
ofthe rim near the edge. (See Diag
ram 5)
7. Center the bowl over the cutout and slowly lower the lavatory into place, align with the marks made earlier, then press down firmly.
8. Allow sealantto set before connecting supplies and drain .
9. Connect supply line to faucet and supply shut-off valves. Tighten connections atfaucet and shut-off valves for water tight seal. Connecttrap to
drain assembly, first hand tightto check alignmentthen sec ure joints for watertight assembly. (See Diagram 6)
10. CHECK FOR LEAKS!
Limited Warranty
Whatis the Warranty Period?
The warranty is for one year from installation date or purchase of home.
Who Is Covered?
The warranty covers the original purchaser or first home own
er.
What Does the Warranty Cover?
The warranty covers the vitreous china product that is defec
tive in materials or workmanship.
We will repair or replace the product with a replacement mode
l.
What Does the Warranty Not Cover?
Failures to fittings due to chlorine or other chemicals.
Installation and labor costs you incurred.
Repair costs and damage due to leaks from supply line failure
s.
Products not installed per Keller’s instructions.
Product that were subject to abuse or misuse.
Products that do not meet local building code requirements.
Products with faulty maintenance.
What do you do to get Service?
You may contact the place of purchase or call 561-630-0457
.
Tynan Plumbing Fixtures
PO Box 33178
Palm Beach Gardens, FL 33420
Maintenance and Care
Do not use abrasive powder or liquid cleaners which can damage the product surface.
Caution: Productis Fragile. To avoid breakage and possible injury handle with care!
REV 08/2013
Cut-Out Ring
Model 9600
Tools and Supplies Needed for Installation
Installation Instructions
Self-Rim Lavatory
L. Drill
K. Sabre Saw
I. Hacksaw
J. Basin Wrench
H. Pipe Wrench
G. Putty Knife
F. Silicone Caulk
E. Tube Cutter
D. Tape Measure
B. Pliers
C. Adjustable Wrench
A. Regular and Phillip
Screwdriver
RIM LINE
TEMPLATE
CUTOUT LINE
Front
16-1/4” x 13-1/4”
(412mm x 336mm)
Important Installation Notes;
1. These instructions are for typical installations and if your situation is not representative to these instructions, you should consult a
professional.
2. If replacing an existing lavatory be certain to shut off water supply before removing old lavatory.
3. Be sure thatthe counter-top and space under the surface is large enough to accommodate the lavatory and drain assembly.
4. Do to slight variances in the manufacture process itis rec ommended thatthis template is used as a guideline along with the actual fixture
before any counter top is cut. The fixture dimensions should be compared to the template before cutting.
5. Position the lavatory upside down on the counter top making sure the productfits the dimensional limits ofthe surface and vanity.
6. Provide extra supportto the vanity if required by using 2x 4 braces on both sides ofthe sink opening. Attach with screws into the cabinet
framing. Angle brackets with screws shorter than the top and vanity wall thickness can be used to anchor the vanity top to the inside walls of
the vanity. (Angle brackets and screws notfurnished.)
(Caution; Broken vitreous china pieces are sharp and will cause severe cuts, use caution any time handling vitreous china products. Always take
precautions by using proper safety and sanitary protective wear.)
Installation Steps;
1. Mark the centerline ofthe counter top, if center location is desired as well as the centerline ofthe lavatory on the und erside ofthe lavatory.
Turn the lavatory over. Place it on the counter top with the two marks lined up. Trace around the perimeter ofthe lavatory. NOTE: THIS IS
NOT THE CUT OUT LINE; IT IS THE “OUTER BASIN RIM SHAPE”. (See Diagram 1)
2. Using scissors cutthe template outthatis your model numb er and align it with the tracing on the countertop, lay the template inside ofthe line
scribed on the counter-top in step 1. making sure thatthe edg es ofthe template are of equal distance from the lavatory tra ced rim line, tape
and mark the template location. (See Diagram 2)
3. Now cutthe countertop using the template as a guide.
4. Mountthe faucets and drain assembly (notincluded) on you r counter top, following the faucet manufacturer's instructions. (See Diagram 3)
5. Temporarily setthe lavatory into the cut out, check for al ignment and mark the desired location ofthe sink to help guid e you on the final
installation. (See Diagram 4)
6. Remove the lavatory after checking fit and alignment, turn lavatory upside down and apply a generous portion of sealant around the underside
ofthe rim near the edge. (See Diag
ram 5)
7. Center the bowl over the cutout and slowly lower the lavatory into place, align with the marks made earlier, then press down firmly.
8. Allow sealantto set before connecting supplies and drain .
9. Connect supply line to faucet and supply shut-off valves. Tighten connections atfaucet and shut-off valves for water tight seal. Connecttrap to
drain assembly, first hand tightto check alignmentthen sec ure joints for watertight assembly. (See Diagram 6)
10. CHECK FOR LEAKS!
Limited Warranty
Whatis the Warranty Period?
The warranty is for one year from installation date or purchase of home.
Who Is Covered?
The warranty covers the original purchaser or first home own
er.
What Does the Warranty Cover?
The warranty covers the vitreous china product that is defec
tive in materials or workmanship.
We will repair or replace the product with a replacement mode
l.
What Does the Warranty Not Cover?
Failures to fittings due to chlorine or other chemicals.
Installation and labor costs you incurred.
Repair costs and damage due to leaks from supply line failure
s.
Products not installed per Keller’s instructions.
Product that were subject to abuse or misuse.
Products that do not meet local building code requirements.
Products with faulty maintenance.
What do you do to get Service?
You may contact the place of purchase or call 561-630-0457
.
Tynan Plumbing Fixtures
PO Box 33178
Palm Beach Gardens, FL 33420
Maintenance and Care
Do not use abrasive powder or liquid cleaners which can damage the product surface.
Caution: Productis Fragile. To avoid breakage and possible injury handle with care!
REV 08/2013
INSTALLATION
(FIG.2)
2. Using scissors cut the template out that
is your model number and align it with the
tracing on the countertop, lay the template
inside of the line scribed on the count-
er-top in step 1. making sure that the edg-
es of the template are of equal distance
from the lavatory traced rim line, tape and
mark the template location.
INSTALLATION
(FIG.2)
2. À l’aide de ciseaux, découper le gab-
arit qui correspond au numéro de votre
modèle et l’aligner avec le tracé sur le
comptoir, étaler le gabarit à l’intérieur de
la ligne tracée sur le comptoir à l’étape
1 en vous assurant que les rebords du
gabarit soient à égale distance de la ligne
tracée du
INSTALACIÓN
(FIGURA 2)
2. Usando unas tijeras, cortar la plantilla
correspondiente al número de su modelo
y alinearla con el trazo de la cubierta. Co-
locar la plantilla dentro de la línea trazada
en la cubierta en el paso 1, asegurándose
de que los bordes de la plantilla tengan la
misma distancia desde el borde del lavabo
que trazó, pegar con cinta y marcar la
ubicación de la plantilla.
(FIG.1)
(FIG.2)
LIGNE DE
COUPE
LÍNEA DE
CORTE
GABARIT
PLANTILLA
LIGNE DU
REBORD
LÍNEA DEL
BORDE
