4
• Place the tank-to-bowl gasket onto the
locknut on the flush valve shank against
the bottom of the tank (Be sure locknut
is tight).
• Position tank on bowl by centering gasket
on bowl inlet.
• Insert bolts through holes inside tank and
down through holes in the bowl making
sure tank is level.
• Assemble washers and nuts to tank bolts.
Alternately tighten nuts so that tank stays
level.
• Be sure nuts are tight enough to achieve a
watertight seal.
Do not overtighten.
CAUTION
Risk of product damage.
Overtightening may cause breakage or
chipping of vitreous china.
3
Bolt
Bolt
Tank to bowl
gasket
Locknut
Bolt
Rubber washer
Metal washer
Rubber washer
Rubber washer
Nut
Nut
Metal washer
• Install or relocate the supply and outlet as
necessary to conform to the roughing-in
dimensions.
• Install a supply shut-off valve.
• Lay the toilet down onto a padded surface.
• From the bottom of toilet, firmly press
a new wax seal around toilet outlet.
• Remove temporary rag (if used) from
toilet flange hole.
• Align and lower toilet over flange and bolts.
• Apply your full body weight around the toilet
to set seal
Bottom of bowl
Wax seal
• Place bolt cap bases over bolt.
• Place metal washers and nuts on plastic bolt
cap bases and bolts.
• Carefully tighten nuts.
• If bolts extend more than 1/4” (6 mm) over
top of the nuts, cut off excess.
• Attach bolt caps.
Bolt
Closet flange
Bolt Cap
Nut
Washer
Bolt Cap Base
Bolt
CAUTION
Risk of external leakage.
Do not lift or rock the bowl after
placement. If you break the watertight
seal, you must install a new wax seal.
Bolt
Hacksaw
Gasket
Bowl inlet
Locknut
Rubber washer
Nut
Metal washer
CAUTION
Risk of product damage.
Overtightening may cause breakage or
chipping of vitreous china.
CAUTION
Risk of product damage.
Protect the vitreous china from exposure
to the saw blade when cutting off
excess bolt length.
• Install or relocate the supply and outlet as
necessary to conform to the roughing-in
dimensions.
• Install a supply shut-off valve.
• Lay the toilet down onto a padded surface.
• Carefully inspect the new toilet for damage.
• If the existing toilet does not have a supply
shut-off valve below the tank, install one
before installing the new toilet.
• Place bolt cap bases over bolt.
• Place metal washers and nuts on plastic bolt
cap bases and bolts.
• Carefully tighten nuts.
• If bolts extend more than 1/4” (6 mm) over
top of the nuts, cut off excess.
• Attached bolt caps.
• Align and lower toilet over flange and bolts.
• Apply your full body weight around the
toilet to set seal
• Carefully inspect the new toilet for damage.
• If the existing toilet does not have a supply
shut-off valve below the tank, install one
before installing the new toilet.
• Position tank on bowl by centering gasket
on bowl inlet.
• Insert bolts through holes inside tank and
down through holes in bowl making sure
tank is level.
• Assemble washers and nuts to tank bolts.
Alternately tighten nuts so that tank stays
level.
• Be sure suts are tight enough to achieve a
watertight seal.
Do not overtighten.
2. INSTALL THE NEW TOILET
3. INSTALL THE TANK
4
• Place the tank-to-bowl gasket onto the
locknut on the flush valve shank against
the bottom of the tank (Be sure locknut
is tight).
• Position tank on bowl by centering gasket
on bowl inlet.
• Insert bolts through holes inside tank and
down through holes in the bowl making
sure tank is level.
• Assemble washers and nuts to tank bolts.
Alternately tighten nuts so that tank stays
level.
• Be sure nuts are tight enough to achieve a
watertight seal.
Do not overtighten.
CAUTION
Risk of product damage.
Overtightening may cause breakage or
chipping of vitreous china.
3
Bolt
Bolt
Tank to bowl
gasket
Locknut
Bolt
Rubber washer
Metal washer
Rubber washer
Rubber washer
Nut
Nut
Metal washer
• Install or relocate the supply and outlet as
necessary to conform to the roughing-in
dimensions.
• Install a supply shut-off valve.
• Lay the toilet down onto a padded surface.
• From the bottom of toilet, firmly press
a new wax seal around toilet outlet.
• Remove temporary rag (if used) from
toilet flange hole.
• Align and lower toilet over flange and bolts.
• Apply your full body weight around the toilet
to set seal
Bottom of bowl
Wax seal
• Place bolt cap bases over bolt.
• Place metal washers and nuts on plastic bolt
cap bases and bolts.
• Carefully tighten nuts.
• If bolts extend more than 1/4” (6 mm) over
top of the nuts, cut off excess.
• Attach bolt caps.
Bolt
Closet flange
Bolt Cap
Nut
Washer
Bolt Cap Base
Bolt
CAUTION
Risk of external leakage.
Do not lift or rock the bowl after
placement. If you break the watertight
seal, you must install a new wax seal.
Bolt
Hacksaw
Gasket
Bowl inlet
Locknut
Rubber washer
Nut
Metal washer
CAUTION
Risk of product damage.
Overtightening may cause breakage or
chipping of vitreous china.
CAUTION
Risk of product damage.
Protect the vitreous china from exposure
to the saw blade when cutting off
excess bolt length.
• Install or relocate the supply and outlet as
necessary to conform to the roughing-in
dimensions.
• Install a supply shut-off valve.
• Lay the toilet down onto a padded surface.
• Carefully inspect the new toilet for damage.
• If the existing toilet does not have a supply
shut-off valve below the tank, install one
before installing the new toilet.
• Place bolt cap bases over bolt.
• Place metal washers and nuts on plastic bolt
cap bases and bolts.
• Carefully tighten nuts.
• If bolts extend more than 1/4” (6 mm) over
top of the nuts, cut off excess.
• Attached bolt caps.
• Align and lower toilet over flange and bolts.
• Apply your full body weight around the
toilet to set seal
• Carefully inspect the new toilet for damage.
• If the existing toilet does not have a supply
shut-off valve below the tank, install one
before installing the new toilet.
• Position tank on bowl by centering gasket
on bowl inlet.
• Insert bolts through holes inside tank and
down through holes in bowl making sure
tank is level.
• Assemble washers and nuts to tank bolts.
Alternately tighten nuts so that tank stays
level.
• Be sure suts are tight enough to achieve a
watertight seal.
Do not overtighten.
2. INSTALL THE NEW TOILET
3. INSTALL THE TANK
4
• Place the tank-to-bowl gasket onto the
locknut on the flush valve shank against
the bottom of the tank (Be sure locknut
is tight).
• Position tank on bowl by centering gasket
on bowl inlet.
• Insert bolts through holes inside tank and
down through holes in the bowl making
sure tank is level.
• Assemble washers and nuts to tank bolts.
Alternately tighten nuts so that tank stays
level.
• Be sure nuts are tight enough to achieve a
watertight seal.
Do not overtighten.
CAUTION
Risk of product damage.
Overtightening may cause breakage or
chipping of vitreous china.
3
Bolt
Bolt
Tank to bowl
gasket
Locknut
Bolt
Rubber washer
Metal washer
Rubber washer
Rubber washer
Nut
Nut
Metal washer
• Install or relocate the supply and outlet as
necessary to conform to the roughing-in
dimensions.
• Install a supply shut-off valve.
• Lay the toilet down onto a padded surface.
• From the bottom of toilet, firmly press
a new wax seal around toilet outlet.
• Remove temporary rag (if used) from
toilet flange hole.
• Align and lower toilet over flange and bolts.
• Apply your full body weight around the toilet
to set seal
Bottom of bowl
Wax seal
• Place bolt cap bases over bolt.
• Place metal washers and nuts on plastic bolt
cap bases and bolts.
• Carefully tighten nuts.
• If bolts extend more than 1/4” (6 mm) over
top of the nuts, cut off excess.
• Attach bolt caps.
Bolt
Closet flange
Bolt Cap
Nut
Washer
Bolt Cap Base
Bolt
CAUTION
Risk of external leakage.
Do not lift or rock the bowl after
placement. If you break the watertight
seal, you must install a new wax seal.
Bolt
Hacksaw
Gasket
Bowl inlet
Locknut
Rubber washer
Nut
Metal washer
CAUTION
Risk of product damage.
Overtightening may cause breakage or
chipping of vitreous china.
CAUTION
Risk of product damage.
Protect the vitreous china from exposure
to the saw blade when cutting off
excess bolt length.
• Install or relocate the supply and outlet as
necessary to conform to the roughing-in
dimensions.
• Install a supply shut-off valve.
• Lay the toilet down onto a padded surface.
• Carefully inspect the new toilet for damage.
• If the existing toilet does not have a supply
shut-off valve below the tank, install one
before installing the new toilet.
• Place bolt cap bases over bolt.
• Place metal washers and nuts on plastic bolt
cap bases and bolts.
• Carefully tighten nuts.
• If bolts extend more than 1/4” (6 mm) over
top of the nuts, cut off excess.
• Attached bolt caps.
• Align and lower toilet over flange and bolts.
• Apply your full body weight around the
toilet to set seal
• Carefully inspect the new toilet for damage.
• If the existing toilet does not have a supply
shut-off valve below the tank, install one
before installing the new toilet.
• Position tank on bowl by centering gasket
on bowl inlet.
• Insert bolts through holes inside tank and
down through holes in bowl making sure
tank is level.
• Assemble washers and nuts to tank bolts.
Alternately tighten nuts so that tank stays
level.
• Be sure suts are tight enough to achieve a
watertight seal.
Do not overtighten.
2. INSTALL THE NEW TOILET
3. INSTALL THE TANK
4
• Place the tank-to-bowl gasket onto the
locknut on the flush valve shank against
the bottom of the tank (Be sure locknut
is tight).
• Position tank on bowl by centering gasket
on bowl inlet.
• Insert bolts through holes inside tank and
down through holes in the bowl making
sure tank is level.
• Assemble washers and nuts to tank bolts.
Alternately tighten nuts so that tank stays
level.
• Be sure nuts are tight enough to achieve a
watertight seal.
Do not overtighten.
CAUTION
Risk of product damage.
Overtightening may cause breakage or
chipping of vitreous china.
3
Bolt
Bolt
Tank to bowl
gasket
Locknut
Bolt
Rubber washer
Metal washer
Rubber washer
Rubber washer
Nut
Nut
Metal washer
• Install or relocate the supply and outlet as
necessary to conform to the roughing-in
dimensions.
• Install a supply shut-off valve.
• Lay the toilet down onto a padded surface.
• From the bottom of toilet, firmly press
a new wax seal around toilet outlet.
• Remove temporary rag (if used) from
toilet flange hole.
• Align and lower toilet over flange and bolts.
• Apply your full body weight around the toilet
to set seal
Bottom of bowl
Wax seal
• Place bolt cap bases over bolt.
• Place metal washers and nuts on plastic bolt
cap bases and bolts.
• Carefully tighten nuts.
• If bolts extend more than 1/4” (6 mm) over
top of the nuts, cut off excess.
• Attach bolt caps.
Bolt
Closet flange
Bolt Cap
Nut
Washer
Bolt Cap Base
Bolt
CAUTION
Risk of external leakage.
Do not lift or rock the bowl after
placement. If you break the watertight
seal, you must install a new wax seal.
Bolt
Hacksaw
Gasket
Bowl inlet
Locknut
Rubber washer
Nut
Metal washer
CAUTION
Risk of product damage.
Overtightening may cause breakage or
chipping of vitreous china.
CAUTION
Risk of product damage.
Protect the vitreous china from exposure
to the saw blade when cutting off
excess bolt length.
• Install or relocate the supply and outlet as
necessary to conform to the roughing-in
dimensions.
• Install a supply shut-off valve.
• Lay the toilet down onto a padded surface.
• Carefully inspect the new toilet for damage.
• If the existing toilet does not have a supply
shut-off valve below the tank, install one
before installing the new toilet.
• Place bolt cap bases over bolt.
• Place metal washers and nuts on plastic bolt
cap bases and bolts.
• Carefully tighten nuts.
• If bolts extend more than 1/4” (6 mm) over
top of the nuts, cut off excess.
• Attached bolt caps.
• Align and lower toilet over flange and bolts.
• Apply your full body weight around the
toilet to set seal
• Carefully inspect the new toilet for damage.
• If the existing toilet does not have a supply
shut-off valve below the tank, install one
before installing the new toilet.
• Position tank on bowl by centering gasket
on bowl inlet.
• Insert bolts through holes inside tank and
down through holes in bowl making sure
tank is level.
• Assemble washers and nuts to tank bolts.
Alternately tighten nuts so that tank stays
level.
• Be sure suts are tight enough to achieve a
watertight seal.
Do not overtighten.
2. INSTALL THE NEW TOILET
3. INSTALL THE TANK
4
• Place the tank-to-bowl gasket onto the
locknut on the flush valve shank against
the bottom of the tank (Be sure locknut
is tight).
• Position tank on bowl by centering gasket
on bowl inlet.
• Insert bolts through holes inside tank and
down through holes in the bowl making
sure tank is level.
• Assemble washers and nuts to tank bolts.
Alternately tighten nuts so that tank stays
level.
• Be sure nuts are tight enough to achieve a
watertight seal.
Do not overtighten.
CAUTION
Risk of product damage.
Overtightening may cause breakage or
chipping of vitreous china.
3
Bolt
Bolt
Tank to bowl
gasket
Locknut
Bolt
Rubber washer
Metal washer
Rubber washer
Rubber washer
Nut
Nut
Metal washer
• Install or relocate the supply and outlet as
necessary to conform to the roughing-in
dimensions.
• Install a supply shut-off valve.
• Lay the toilet down onto a padded surface.
• From the bottom of toilet, firmly press
a new wax seal around toilet outlet.
• Remove temporary rag (if used) from
toilet flange hole.
• Align and lower toilet over flange and bolts.
• Apply your full body weight around the toilet
to set seal
Bottom of bowl
Wax seal
• Place bolt cap bases over bolt.
• Place metal washers and nuts on plastic bolt
cap bases and bolts.
• Carefully tighten nuts.
• If bolts extend more than 1/4” (6 mm) over
top of the nuts, cut off excess.
• Attach bolt caps.
Bolt
Closet flange
Bolt Cap
Nut
Washer
Bolt Cap Base
Bolt
CAUTION
Risk of external leakage.
Do not lift or rock the bowl after
placement. If you break the watertight
seal, you must install a new wax seal.
Bolt
Hacksaw
Gasket
Bowl inlet
Locknut
Rubber washer
Nut
Metal washer
CAUTION
Risk of product damage.
Overtightening may cause breakage or
chipping of vitreous china.
CAUTION
Risk of product damage.
Protect the vitreous china from exposure
to the saw blade when cutting off
excess bolt length.
• Install or relocate the supply and outlet as
necessary to conform to the roughing-in
dimensions.
• Install a supply shut-off valve.
• Lay the toilet down onto a padded surface.
• Carefully inspect the new toilet for damage.
• If the existing toilet does not have a supply
shut-off valve below the tank, install one
before installing the new toilet.
• Place bolt cap bases over bolt.
• Place metal washers and nuts on plastic bolt
cap bases and bolts.
• Carefully tighten nuts.
• If bolts extend more than 1/4” (6 mm) over
top of the nuts, cut off excess.
• Attached bolt caps.
• Align and lower toilet over flange and bolts.
• Apply your full body weight around the
toilet to set seal
• Carefully inspect the new toilet for damage.
• If the existing toilet does not have a supply
shut-off valve below the tank, install one
before installing the new toilet.
• Position tank on bowl by centering gasket
on bowl inlet.
• Insert bolts through holes inside tank and
down through holes in bowl making sure
tank is level.
• Assemble washers and nuts to tank bolts.
Alternately tighten nuts so that tank stays
level.
• Be sure suts are tight enough to achieve a
watertight seal.
Do not overtighten.
2. INSTALL THE NEW TOILET
3. INSTALL THE TANK
4
• Place the tank-to-bowl gasket onto the
locknut on the flush valve shank against
the bottom of the tank (Be sure locknut
is tight).
• Position tank on bowl by centering gasket
on bowl inlet.
• Insert bolts through holes inside tank and
down through holes in the bowl making
sure tank is level.
• Assemble washers and nuts to tank bolts.
Alternately tighten nuts so that tank stays
level.
• Be sure nuts are tight enough to achieve a
watertight seal.
Do not overtighten.
CAUTION
Risk of product damage.
Overtightening may cause breakage or
chipping of vitreous china.
3
Bolt
Bolt
Tank to bowl
gasket
Locknut
Bolt
Rubber washer
Metal washer
Rubber washer
Rubber washer
Nut
Nut
Metal washer
• Install or relocate the supply and outlet as
necessary to conform to the roughing-in
dimensions.
• Install a supply shut-off valve.
• Lay the toilet down onto a padded surface.
• From the bottom of toilet, firmly press
a new wax seal around toilet outlet.
• Remove temporary rag (if used) from
toilet flange hole.
• Align and lower toilet over flange and bolts.
• Apply your full body weight around the toilet
to set seal
Bottom of bowl
Wax seal
• Place bolt cap bases over bolt.
• Place metal washers and nuts on plastic bolt
cap bases and bolts.
• Carefully tighten nuts.
• If bolts extend more than 1/4” (6 mm) over
top of the nuts, cut off excess.
• Attach bolt caps.
Bolt
Closet flange
Bolt Cap
Nut
Washer
Bolt Cap Base
Bolt
CAUTION
Risk of external leakage.
Do not lift or rock the bowl after
placement. If you break the watertight
seal, you must install a new wax seal.
Bolt
Hacksaw
Gasket
Bowl inlet
Locknut
Rubber washer
Nut
Metal washer
CAUTION
Risk of product damage.
Overtightening may cause breakage or
chipping of vitreous china.
CAUTION
Risk of product damage.
Protect the vitreous china from exposure
to the saw blade when cutting off
excess bolt length.
• Install or relocate the supply and outlet as
necessary to conform to the roughing-in
dimensions.
• Install a supply shut-off valve.
• Lay the toilet down onto a padded surface.
• Carefully inspect the new toilet for damage.
• If the existing toilet does not have a supply
shut-off valve below the tank, install one
before installing the new toilet.
• Place bolt cap bases over bolt.
• Place metal washers and nuts on plastic bolt
cap bases and bolts.
• Carefully tighten nuts.
• If bolts extend more than 1/4” (6 mm) over
top of the nuts, cut off excess.
• Attached bolt caps.
• Align and lower toilet over flange and bolts.
• Apply your full body weight around the
toilet to set seal
• Carefully inspect the new toilet for damage.
• If the existing toilet does not have a supply
shut-off valve below the tank, install one
before installing the new toilet.
• Position tank on bowl by centering gasket
on bowl inlet.
• Insert bolts through holes inside tank and
down through holes in bowl making sure
tank is level.
• Assemble washers and nuts to tank bolts.
Alternately tighten nuts so that tank stays
level.
• Be sure suts are tight enough to achieve a
watertight seal.
Do not overtighten.
2. INSTALL THE NEW TOILET
3. INSTALL THE TANK
4
• Place the tank-to-bowl gasket onto the
locknut on the flush valve shank against
the bottom of the tank (Be sure locknut
is tight).
• Position tank on bowl by centering gasket
on bowl inlet.
• Insert bolts through holes inside tank and
down through holes in the bowl making
sure tank is level.
• Assemble washers and nuts to tank bolts.
Alternately tighten nuts so that tank stays
level.
• Be sure nuts are tight enough to achieve a
watertight seal.
Do not overtighten.
CAUTION
Risk of product damage.
Overtightening may cause breakage or
chipping of vitreous china.
3
Bolt
Bolt
Tank to bowl
gasket
Locknut
Bolt
Rubber washer
Metal washer
Rubber washer
Rubber washer
Nut
Nut
Metal washer
• Install or relocate the supply and outlet as
necessary to conform to the roughing-in
dimensions.
• Install a supply shut-off valve.
• Lay the toilet down onto a padded surface.
• From the bottom of toilet, firmly press
a new wax seal around toilet outlet.
• Remove temporary rag (if used) from
toilet flange hole.
• Align and lower toilet over flange and bolts.
• Apply your full body weight around the toilet
to set seal
Bottom of bowl
Wax seal
• Place bolt cap bases over bolt.
• Place metal washers and nuts on plastic bolt
cap bases and bolts.
• Carefully tighten nuts.
• If bolts extend more than 1/4” (6 mm) over
top of the nuts, cut off excess.
• Attach bolt caps.
Bolt
Closet flange
Bolt Cap
Nut
Washer
Bolt Cap Base
Bolt
CAUTION
Risk of external leakage.
Do not lift or rock the bowl after
placement. If you break the watertight
seal, you must install a new wax seal.
Bolt
Hacksaw
Gasket
Bowl inlet
Locknut
Rubber washer
Nut
Metal washer
CAUTION
Risk of product damage.
Overtightening may cause breakage or
chipping of vitreous china.
CAUTION
Risk of product damage.
Protect the vitreous china from exposure
to the saw blade when cutting off
excess bolt length.
• Install or relocate the supply and outlet as
necessary to conform to the roughing-in
dimensions.
• Install a supply shut-off valve.
• Lay the toilet down onto a padded surface.
• Carefully inspect the new toilet for damage.
• If the existing toilet does not have a supply
shut-off valve below the tank, install one
before installing the new toilet.
• Place bolt cap bases over bolt.
• Place metal washers and nuts on plastic bolt
cap bases and bolts.
• Carefully tighten nuts.
• If bolts extend more than 1/4” (6 mm) over
top of the nuts, cut off excess.
• Attached bolt caps.
• Align and lower toilet over flange and bolts.
• Apply your full body weight around the
toilet to set seal
• Carefully inspect the new toilet for damage.
• If the existing toilet does not have a supply
shut-off valve below the tank, install one
before installing the new toilet.
• Position tank on bowl by centering gasket
on bowl inlet.
• Insert bolts through holes inside tank and
down through holes in bowl making sure
tank is level.
• Assemble washers and nuts to tank bolts.
Alternately tighten nuts so that tank stays
level.
• Be sure suts are tight enough to achieve a
watertight seal.
Do not overtighten.
2. INSTALL THE NEW TOILET
3. INSTALL THE TANK
4
• Place the tank-to-bowl gasket onto the
locknut on the flush valve shank against
the bottom of the tank (Be sure locknut
is tight).
• Position tank on bowl by centering gasket
on bowl inlet.
• Insert bolts through holes inside tank and
down through holes in the bowl making
sure tank is level.
• Assemble washers and nuts to tank bolts.
Alternately tighten nuts so that tank stays
level.
• Be sure nuts are tight enough to achieve a
watertight seal.
Do not overtighten.
CAUTION
Risk of product damage.
Overtightening may cause breakage or
chipping of vitreous china.
3
Bolt
Bolt
Tank to bowl
gasket
Locknut
Bolt
Rubber washer
Metal washer
Rubber washer
Rubber washer
Nut
Nut
Metal washer
• Install or relocate the supply and outlet as
necessary to conform to the roughing-in
dimensions.
• Install a supply shut-off valve.
• Lay the toilet down onto a padded surface.
• From the bottom of toilet, firmly press
a new wax seal around toilet outlet.
• Remove temporary rag (if used) from
toilet flange hole.
• Align and lower toilet over flange and bolts.
• Apply your full body weight around the toilet
to set seal
Bottom of bowl
Wax seal
• Place bolt cap bases over bolt.
• Place metal washers and nuts on plastic bolt
cap bases and bolts.
• Carefully tighten nuts.
• If bolts extend more than 1/4” (6 mm) over
top of the nuts, cut off excess.
• Attach bolt caps.
Bolt
Closet flange
Bolt Cap
Nut
Washer
Bolt Cap Base
Bolt
CAUTION
Risk of external leakage.
Do not lift or rock the bowl after
placement. If you break the watertight
seal, you must install a new wax seal.
Bolt
Hacksaw
Gasket
Bowl inlet
Locknut
Rubber washer
Nut
Metal washer
CAUTION
Risk of product damage.
Overtightening may cause breakage or
chipping of vitreous china.
CAUTION
Risk of product damage.
Protect the vitreous china from exposure
to the saw blade when cutting off
excess bolt length.
• Install or relocate the supply and outlet as
necessary to conform to the roughing-in
dimensions.
• Install a supply shut-off valve.
• Lay the toilet down onto a padded surface.
• Carefully inspect the new toilet for damage.
• If the existing toilet does not have a supply
shut-off valve below the tank, install one
before installing the new toilet.
• Place bolt cap bases over bolt.
• Place metal washers and nuts on plastic bolt
cap bases and bolts.
• Carefully tighten nuts.
• If bolts extend more than 1/4” (6 mm) over
top of the nuts, cut off excess.
• Attached bolt caps.
• Align and lower toilet over flange and bolts.
• Apply your full body weight around the
toilet to set seal
• Carefully inspect the new toilet for damage.
• If the existing toilet does not have a supply
shut-off valve below the tank, install one
before installing the new toilet.
• Position tank on bowl by centering gasket
on bowl inlet.
• Insert bolts through holes inside tank and
down through holes in bowl making sure
tank is level.
• Assemble washers and nuts to tank bolts.
Alternately tighten nuts so that tank stays
level.
• Be sure suts are tight enough to achieve a
watertight seal.
Do not overtighten.
2. INSTALL THE NEW TOILET
3. INSTALL THE TANK
2. INSTALL THE NEW TOILET
3. INSTALL THE TANK
• Install or relocate the supply and outlet as
necessary to conform to the roughing-in
dimensions.
• Install a supply shut-off valve.
• Lay the toilet down onto a padded surface.
• Carefully inspect the new toilet for damage.
• If the existing toilet does not have a supply
shut-off valve below the tank, install one
before installing the new toilet.
• Place bolt cap bases over bolt.
• Place metal washers and nuts on plastic bolt
cap bases and bolts.
• Carefully tighten nuts.
• If bolts extend more than 1/4” (6 mm) over
top of the nuts, cut off excess.
• Attach bolt caps.
• Carefully inspect the new toilet for damage.
• If the existing toilet does not have a supply
shut-off valve below the tank, install one
before installing the new toilet.
• Align and lower toilet over flange and bolts.
• Apply your full body weight around the toilet
to set seal.
• Position tank on bowl by centering gasket
on bowl inlet.
• Assemble washers and nuts to tank bolts.
Alternately tighten nuts so that tank stays level.
• Insert bolts through holes inside tank and
down through holes in the bowl making
sure tank is level.
• Be sure nuts are tight enough to achieve a
watertight seal.
Do not overtighten.
4
3
Risk of external leakage.
Do not lift or rock the bowl after
placement. If you break the watertight
seal, you must install a new wax seal.
Risk of product damage.
Overtightening may cause breakage or
chipping of vitreous china.
Risk of product damage.
Overtightening may cause breakage or
chipping of vitreous china.
CAUTION
CAUTION
CAUTION
Risk of product damage.
Protect the vitreous china from exposure
to the saw blade when cutting off
excess bolt length.
CAUTION
