Mira Zest 7.5 Installation, Operation And Maintenance Manual Download Page 5

5

Caution!

2.1. Read all of these instructions and retain this guide for later use

.

2.2.

Pass on this guide in the event of change of ownership of the installation site.

2.3.

Follow all warnings, cautions and instructions contained in this guide, and on or
inside the appliance.

2.4.

The electrical installation must comply with the “Requirements for Electrical
Installations” commonly referred to as the IEE Wiring Regulations, or any particular
regulations and practices, specified by the local electricity supply company in force
at the time of installation. The installation should be carried out by an electrician or
contractor who is registered, or is a member of, an association such as:

2.4.1. 

National Inspection Council for Electrical Installation and Contracting (NICEIC),

throughout the UK.

2.4.2.

 The Electrical Contractors Association (ECA), England and Wales.

2.4.3. 

The Electrical Contractors Association of Scotland (ECAS).

2.5.

This is a high power unit; it is essential to contact your electricity supply company
to ensure that the electricity supply is adequate for the purpose.

2.6.

The plumbing installation must comply with the requirements of UK Water
Regulations/Bye-laws (Scotland), Building Regulations or any particular regulations
and practices, specified by the local water company or water undertakers. The
installation should be carried out by a plumber or contractor who is registered, or is
a member of, an association such as:

2.6.1. 

Institute of Plumbing (IOP), throughout the UK.

2.6.2. 

National Association of Plumbing, Heating and Mechanical Services

Contractors (NAPH & MSC), England and Wales.

2.6.3. 

Scottish and Northern Ireland Plumbing Employers’ Federation (SNIPEF),

Scotland and Northern Ireland.

2.7.

Anyone who may have difficulty understanding or operating the controls of any
shower should be attended whilst showering. Particular consideration should be
given to the young, the elderly, the infirm, or anyone inexperienced in the correct
operation of the controls.

2.8.

When this appliance has reached the end of its serviceable life, it should be disposed
of in a safe manner, in accordance with current local authority recycling, or waste
disposal policy.

Summary of Contents for Zest 7.5

































Reviews: