Mira Miniduo Installation & User Manual Download Page 18

18

30.

Check that the blue ‘O’ seal is fitted inside the 

backplate nut. Fit the olive and the backplate 

nut over the outlet pipe and loosely tighten 

the nut.

31.

 To prevent the backplate from turning while 

tightening the nut, fit the retaining ring over the 

backplate nut making sure the slots engage 

with the screws on the backplate, hold the 

retaining ring with a wrench while tightening 

the backplate nut. Remove the retaining ring 

after use.

32. 

Check that the second ‘O’ seal (black) is fitted 

to the outside of the backplate nut. Press the 

elbow onto the backplate, make sure that the 

clips on the elbow engage with the backplate.

33.

 Slide the retaining ring over the elbow and 

engage with the elbow clips. 

Note! 

The 

retaining ring must be engaged correctly to 

lock the elbow to the backplate, rotate the 

retaining ring to the postition illustrated.

1

2

34. 

Press the shroud over the elbow, make sure 

that it engages with the lugs on the backplate.

35. 

Fit the concealing ring over the mixer and mark 

the positions of the three fixing holes.

36. 

For solid walls drill three 6 mm holes for the 

wall plugs. For other types of wall structure 

alternative fixings may be required (not 

supplied).

 

Caution! 

Make sure that you do not drill into 

pipework in the wall.

37.

 Insert the wall plugs (supplied) and attach the 

concealing ring to the wall with the screws 

provided.

 

Important! 

Apply silicone sealant to the 

groove on the rear face of the concealing ring

38.

 Fit the concealing plate to the concealing ring.

39. 

Refit the control knobs.

40 

Fit  the  shower  fittings,  refer  to  your  shower 

fittings installation and user guide for 

instructions.

 Important!

 For high pressure systems (above 

0.5  bar)  make  sure  that  the  flow  regulator 

(supplied)  is  fitted,  refer  to  section: 

‘Flow 

Regulators’

.

41. 

Turn on the hot and cold water supplies and 

check for leaks.

42. 

Before using the shower, refer to section: 

‘Commissioning’

.

Backplate Nut

Retaining Ring

Olive

Concealing Ring

Apply Silicone 

Sealant

Screws

Retaining Ring shown 

correctly engaged with 

Elbow

Elbow

Slot

Screw

Summary of Contents for Miniduo

































Reviews: