Mira Coda Installation & User Manual Download Page 20

20

1065367-W2-E (1630) (H04A)

© Kohler Mira Limited, April 2008

CusToMer serVICe

Guarantee of Quality

Mira Showers guarantee your product against any defect 

in materials or workmanship for the period shown in the 

Guarantee  Registration  Document  included  with  your 

shower.

Alternatively,  to  confi rm  the  applicable  guarantee  period 

please contact Customer Services.

To validate the guarantee, please return your completed 

registration card.

Within the guarantee period we will resolve defects, free 

of charge, by repairing or replacing parts or modules as 

we may choose.

To be free of charge, service work must only be undertaken 

by Mira Showers or our approved agents.

Service  under  this  guarantee  does  not  affect  the  expiry 

date.

The guarantee on any exchanged parts or product ends 

when the normal product guarantee period expires.

Not covered by this guarantee:

Planned  maintenance,  or  replacement  parts  required  to 

comply with the servicing requirements of the TMV 2 and 

TMV 3 healthcare schemes.

Damage  or  defects  arising  from  incorrect  installation, 

improper  use  or  lack  of  maintenance, including  build-up 

of limescale.

Damage or defects if the product is taken apart, repaired or 

modifi ed by any persons not authorised by Mira Showers 

or our approved agents.

This guarantee is in addition to your statutory and other 

legal rights.

What to do if something goes wrong

If  when  you  first  use  your  shower,  it  doesn’t  function 

correctly, fi rst contact your installer to check that installation 

and commissioning are satisfactory and in accordance with 

the instructions in this manual. We are on hand to offer you 

or your installer any advice you may need.

Should  this  not  resolve  the  diffi culty,  simply  contact  our 

Customer Services Team who will give every assistance 

and,  if  necessary,  arrange  for  our  service  engineer  to 

visit. If the performance of your shower declines, consult 

this manual to see whether simple home maintenance is 

required. Please call our Customer Services Team to talk 

the diffi culty through, request a service under guarantee 

if  applicable,  or  take  advantage  of  our  comprehensive 

After-Sales service.

As part of our quality and training programme calls may be 

recorded or monitored.

Our Customer Services Team is comprehensively trained to 

provide every assistance you may need: help and advice, 

spare parts or a service visit.

Spare Parts

We maintain an extensive stock of spares and aim to provide 

support throughout the product’s expected life.

Spares  can  be  purchased  from  approved  stockists  or 

merchants (locations on request) or direct from Customer 

Services.

Spares direct will normally be despatched within two working 

days. Payment can be made by Visa or MasterCard at the 

time of ordering. Should payment by cheque be preferred, 

a pro-forma invoice will be sent.

All  spares  are  guaranteed  for  12  months  from  date  of 

purchase. Spares that have been supplied directly from us 

can be returned within one month from date of purchase, 

providing that they are in good order and the packaging 

is unopened.

Note!

 Returned spares will be subject to a 15% restocking 

charge and authorisation must be obtained before return. 

Please contact our Customer Services Team.

Note! 

In the interests of safety, spares requiring exposure 

to mains voltages can only be sent to competent persons.

Service

Our Service Force is available to provide a quality service 

at a reasonable cost. You will have the assurance of a Mira 

trained  engineer/agent,  genuine  Mira  spare  parts  and  a 

12 month guarantee on the repair.

Payment  should  be  made  directly  to  the  engineer/agent 

using  Visa,  MasterCard  or  a  cheque  supported  by  a 

banker’s card.

To Contact Us

England, Scotland, Wales and Northern Ireland

Mira Showers Customer Services

Telephone: 0870 241 0888, Mon to Fri 8:00 am - 5:30 pm

 

 

Sat 8:30 am - 3:30 pm

E-mail: 

[email protected]

Fax: 

01242 282595

By Post:  Cromwell Road, Cheltenham,

 

Gloucestershire, GL52 5EP

Eire

Modern Plant Ltd (Dublin)

Telephone: 01 459 1344,  Mon to Fri 9:00 am - 5:00 pm

E-mail: 

[email protected]

Fax: 

Dublin 01 459 2329

Post: 

Otter House, Naas Road,

 

Clondalkin, Dublin 22

Modern Plant (Cork)

Telephone: 021 496 8755,  Mon to Fri 9:00 am - 5:00 pm

E-mail: 

[email protected]

Fax: 

021 496 8607

Post: 

Tramore Road, Cork

Mira is a registered trade mark of 

Kohler Mira Limited.

The company reserves the right to alter 

product specifi cations without notice.

www.mirashowers.com

Summary of Contents for Coda





















Reviews: