background image

FOR COMMERCIAL USE ONLY 

IMPORTANT SAFETY INSTRUCTIONS

 

 
 

When using an electrical appliance, basic precautions should always be followed, including the following: 

 

READ ALL INSTRUCTIONS BEFORE USING 

WARNING - To reduce the risk of fire, electric shock, or injury:

 

 

  Do not leave appliance when plugged in. Unplug from outlet when not in use and before servicing. 

 

 

WARNING 

 

To reduce the risk of electrical shock - Do not expose to rain. Store indoors. 

 

 Never allow children or untrained adults to operate this equipment. 

 Keep the area of operation clear of all persons, particularly small children, and pets. Keep bystanders 

at least 25 feet away from the area of operation. 

 Use only as described in this manual. Use only manufacturer‘s recommended attachments. 

 Do not use with damaged cord or plug. If appliance is not working as it should, has been dropped, 

damaged, left outdoors, or dropped into water, return it to a service center. 

 Do not pull or carry by cord, use cord as a handle, close a door on cord, or pull cord around sharp 

edges or corners. Do not run appliance over cord. Keep cord away from heated surfaces. 

 Do not unplug by pulling on cord. To unplug, grasp the plug, not the cord. 

 Do not handle plug or appliance with wet hands. 

 Do not put any object into openings. Do not use with any opening blocked; keep free of dust, lint, hair, 

and anything that may reduce air flow. 

 Keep hair, loose clothing, fingers, and all parts of body away from openings and moving parts. 

 Turn off all controls before unplugging. 

 Connect to a properly grounded outlet only. See grounding instructions. 

 

 

 

 

 

SAVE THESE INSTRUCTIONS 

 

Summary of Contents for FR17115













Reviews: