background image

Page 7

the new owner/operator and have 
the transfer certifi ed!

• 

The warning and instruction 
plates attached to the machine 
contain valuable advice about safe 
operation. Immediately replace 
incomplete or illegible labels.

• 

For safety standards spare parts 
must be equal to genuine parts!

1.3 Provisions for Operation

• 

Before the fi rst operation of the 
machine, fully charge the battery 
with an initial charging procedure 
and comply with the operating 
instructions of the charger as 
well as with those of the battery 
manufacturer. Minuteman cannot 
be held liable for damages 
resulting from the fact that 
the initial charging has not or 
insuffi  ciently done.

• 

Before operation, check 
the machine for operational 
safety! 

Immediately remedy 

malfunctions!

• 

It is necessary for the operator to 
get acquainted with all attachments 

and controls as well as with their 
function before operation begins. 

• 

When operating the machine use 
of fi rm and skid proof shoes is 
recommended.

• 

The machine may be used only on 
such surfaces clearly specifi ed by the 
owner or his authorized representative.

• 

When operating the machine take 
notice of  persons within the operation 
area especially children.

• 

Start moving immediately after brush 
head has lowered otherwise the brush 
might leave traces on the surface. 
Lift the brush head before going over 
obstacles (doorsteps).

• 

Empty dirty water tank before folding 
recovery tank over. 

• 

Use only cleaning agents suitable for 
automatic machines (low-foaming) 
and comply with the instructions for 
use, disposal and with the warning 
information specifi ed by the cleaning 
agent’s manufacturer.

• 

The machine is not designed for 
collecting hazardous, infl ammable or 
explosive dust or substances.

• 

Usage of the machine in explosive 
areas is prohibited.

• 

Pull the ignition key to avoid 
unauthorized use of the machine.

• 

Before transporting the machine, lift 
the squeegee and the scrub head 
assemblies. Adapt operation of 
machine to the local conditions.

• 

The machine may be used only for 
operation on plane areas with a 
maximum inclination of 2 %.

1.4 Maintenance instructions

• 

The daily and weekly maintenance 
and repair task must be performed 
by a qualifi ed operator. For any 
maintenance and repair work 
beyond this please contact your local 
Minuteman service center.

• 

Observe the maintenance activities 
and intervals set out in the instruction 
manual.

• 

Maintenance and repair work 
should be carried out with use of the 
appropriate tools.

• 

Have the machine checked for 
safety conditions in the sense of the 

Summary of Contents for E28







































Reviews: