6) OPERATING INSTRUCTIONS
Make sure the DC output leads are connected properly to the batteries. Double check the polarities of the output leads. See diagram on page 6.
INDICATOR LIGHTS:
To begin charging, connect the charger to AC power. The following will be displayed on the charger:
1) A GREEN power light is lit to indicate AC power is applied.
2) A YELLOW light is lit for each bank to indicate the battery is charging.
3) A GREEN light is lit for each bank to indicate the battery is fully charged and in maintenance mode.
4) A RED light for each bank is lit if any of the following apply:
a) No battery is connected to an output cord.
b) The battery voltage is below 4.0 volts. The bank will not charge a battery in this condition. (see note below)
c) The battery is connected reverse polarity.
INLINE FUSE:
Each output cord has an inline fuse on the RED lead. This fuse serves as protection from surges and short circuits caused by a damaged char-
ger output cable. If a fuse blows, replace it with the exact type and rating of the original fuse. Improper battery connections will normally not
cause a fuse to blow since this is handled by the chargers internal circuitry.
7) MAINTENANCE / CLEANING / STORAGE INSTRUCTIONS
Check battery charger for dirt, oil, battery corrosion, etc. Use a water and baking soda solution for cleaning corrosion. Wipe clean using a dry
cloth.
Check battery clips for dirt, oil, and battery corrosion; then disconnect from battery posts and clean as necessary with water and baking soda
solution and dry with a clean cloth.
When the charger is not in use, coil the power cord to prevent damage.
If power cord or plug becomes damaged, you may contact the Minn Kota Service Repair Department for service repair information. Otherwise,
dispose of the battery charger in compliance with local law. Damaged cords and plugs can cause electric shock or electrocution.
When storing the battery charger, store in a clean dry area.
NOTE
– A 12 volt battery with an open-circuit voltage below 4 volts has either been discharged to the point of internal damage, may be heavily
sulfated, or may have internal shorted cells. Attempting to charge a battery in this state is dangerous. The battery should be replaced.
CAUTION
– If a RED light is lit, disconnect the AC power from the charger immediately. Determine the reason based on the above information
and take the necessary corrective action to remedy the situation. If you are unable to remedy the situation and need help, call the Minn Kota
Service Department at 1-800-227-6433 and a technical support representative will be happy to assist you.
WARNING
– TO REDUCE RISK OF ELECTRIC SHOCK, DO NOT PERFORM ANY SERVICING OTHER THAN THOSE CONTAINED IN THE
OPERATING INSTRUCTIONS.
CAUTION
– Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to oper-
ate the equipment.
NOTE
– This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates,
uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encour-
aged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
CAUTION
– Generators with a modified square wave output can damage this MINN KOTA charger. Generators with a sine wave output can be
used to power this charger.
Specifications:
Model Part No. System Volts Banks
Output
per Bank
(amps)
Total
Output
(amps)
Input Cable
Output
Cable
Size L x W x H Weight
(lbs)
Input Current
(120VAC, 60Hz)
MK110P 1820110
12
1
10
10
18AWG - 6’ 16AWG - 6’
7” x 9” x 7-3/4”
6.5
1.8A
MK210P 1822110
12 / 24
2
5
10
18AWG - 6’ 16AWG - 6’
7” x 9” x 7-3/4”
6.7
1.8A
5
