5.2.8.2. LULLABIES
You can calm the baby down so it can sleep more easily by means of a soothing lullaby
which will play on the baby's unit. To activate this function, use the buttons (7) and (9)
to choose the lullabies icon (f) and press the remote/accept button (10) to confirm.
Using the buttons and again, choose from between the three lullabies the one you
prefer or disable the lullabies by selecting OFF. Press the remote/accept button (10) again
to confirm the selection.
Bear in mind that the lullabies will only be configured for the camera whose image you are
viewing on the monitor at that time.
5.2.8.3. VOX MODE
This mode lets you control the sound activation of your baby monitor. If you enable the
VOX mode on the monitor and there is no sound around the camera, the latter will stop
transmitting. However, it will keep picking up the sounds using a minimum amount of
power. The monitor screen will go off if the camera is not transmitting. When the camera
detects any sound higher than the sensitivity setting, it will start transmitting the signal to
the monitor again.
To disable this function and see the monitored area continuously, you must disable the
VOX mode on the monitor.
VOX mode disabled: The camera transmits continuously, allowing it to constantly monitor
your baby or the area you wish to monitor
VOX mode enabled: The camera only transmits when a sound is detected with sufficient
intensity - depending on the level selected - around the camera.
Sound sensitivity
Some babies are noisier than others! You can personalise the sensitivity of your baby
monitor to adjust it to your baby. Adjust the "HIGH" sensitivity for a baby sleeping soundly
with faint crying; adjust to LOW sensitivity if the baby usually makes noise whilst sleeping
or makes very loud noises before actually crying; or adjust to a MID level if you think that
your baby's behaviour does not fit in with any of the aforementioned two models.
To activate this function, use the buttons (7) and (9) to select the VOX mode icon (h)
and press the remote/accept button (10) to confirm. Using the buttons and again,
choose whichever of the three camera sensitivity levels available (HIGH/MID/LOW) or
(OFF) you prefer. Press the remote/accept button (10) again to confirm the selection.
Bear in mind that the VOX mode will only be configured for the camera whose image you
are viewing on the monitor at that time.
If you wish to see your baby at a certain time, even if there is no noise about, you
can enable the camera transmission remotely by pressing the remote/accept button
(10).
5.2.8.4. CAMERA VOLUME
This menu will allow you to configure the volume level at which the parents' voices will be
reproduced on the camera by using the two-way function and the volume at which the
lullabies will be heard.
VOX
ENGLISH
30
Summary of Contents for digimonitor 3.5 plus
