Mine Site Technologies MP10-G2 Configuration Manual Download Page 17

FCC Caution. 

 

§ 15.19 Labelling requirements. 

This device complies with part 15 of the FCC Rules. Operation is subject to the 

following two conditions: (1) This device may not cause harmful interference, 

and  (2)  this  device  must  accept  any  interference  received,  including 

interference that may cause undesired operation. 

 

§ 15.21 Changes or modification warning 

Any Changes or modifications not expressly approved by the party responsible 

for compliance could void the user's authority to operate the equipment. 

 

§ 15.105 Information to the user. 
Note:

 This equipment has been tested and found to comply with the limits for a 

Class B digital device, pursuant to part 15 of the FCC Rules. These limits are 

designed  to  provide  reasonable  protection  against  harmful  interference  in  a 

residential installation. This equipment generates uses and can radiate radio 

frequency  energy  and,  if  not  installed  and  used  in  accordance  with  the 

instructions,  may  cause  harmful  interference  to  radio  communications. 

However, there is no guarantee that interference will not occur in a particular 

installation.  If  this  equipment  does  cause  harmful  interference  to  radio  or 

television reception, which can be determined by turning the equipment off and 

on, the user is encouraged to try to correct the interference by one or more of 

the following measures: 

-Reorient or relocate the receiving antenna. 

-Increase the separation between theequipment and receiver. 

-Connect the equipment into an outlet on a circuit different from that to which 

the receiver is connected. 

-Consult the dealer or an experienced radio/TV technician for help. 

 

 

*RF warning for Portable device: 

The device has been evaluated to meet general RF exposure requirement. Th

e device can be used in portable exposure condition without restriction. 

 

This Class [*] digital apparatus complies with Canadian ICES-003. 
Cet appareil numérique de la classe [*] est conforme à la norme NMB-003 du Canada. 

  

RSS-Gen Issue 3 December 2010"&"CNR-Gen 3e éditionDécembre 2010:     

 - English:   This device complies with Industry Canada licence-exempt RSS standard(s).  

 Operation is subject to the following two conditions: 

(1) This device may not cause interference, and

 (2) This device must accept any interference, including interference that may cause undesired 

operation of the device.   

 - French:  Le présentappareilestconforme aux CNR d'Industrie Canada

 applicables aux appareils radio exempts de licence. L'exploitationestautorisée aux deux conditions

 suivantes:   (1) l'appareil ne doit pas produire de brouillage, et   (2) l'utilisateur de l'appareildoit 

accepter tout brouillageradioélectriquesubi, mêmesi le   brouillageest susceptible d'encompromettre 

le fonctionnement.   

Summary of Contents for MP10-G2


















Reviews: