manualshive.com logo in svg

Mindray Passport V, Operating Instructions Manual

The Mindray Passport V is an advanced medical device offering cutting-edge features and technology. Gain comprehensive knowledge about its functionalities and maintenance by accessing the Service Manual, available for free download from our website. Enhance your product understanding and ensure efficient usage of this remarkable equipment.

Share
Download
background image

Clock

Appendix

19 - 4

0070- 0-0704-02

Passport V Operating Instructions

19.3

Clock

Accuracy

±60 sec/30 days in case of 21±3ºC of operating conditions

Range

Jan. 1, 2001 to Dec 31, 2099

Operating Time

Realtime clock is powered by an independent battery which runs for over 5 years.

19.4

Weight and Dimension

Dimension

<30.0 cm (H)  x <18.0 cm (D)  x <32.0cm (W)

Weight

< 11 lb. (5.0kg) (standard configuration, including one battery, local printer)

19.5

Display Specifications

Display Type

Color anti-glare TFT display

Rated display Resolution

800×600(Pixels)

Rated display size

12.1” (246 x 184.4 mm)

Data Update Frequency

≥

 60Hz

Ac/-2Hz

0

Summary of Contents for Passport V

































































































































































































































































































Reviews:

No comments

Related manuals for Passport V

Accent 1200 series Hardware Manual preview
1200 series
Brand: Accent Pages: 42
SportDOG SPORTTRAINER SD-1825E User Manual preview
SPORTTRAINER SD-1825E
Brand: SportDOG Pages: 128
Triple W Japan D Free Quick Start Manual preview
D Free
Brand: Triple W Japan Pages: 8
mychway MS-54W1S User Manual preview
MS-54W1S
Brand: mychway Pages: 73
Gaiam MINI COLD THERAPY PACKS Setup, Tips And Care & Safety Manual preview
MINI COLD THERAPY PACKS
Brand: Gaiam Pages: 2
AbbiDot T30 User Manual preview
T30
Brand: AbbiDot Pages: 24
TUYA SPF-1010-TY Quick Start Manual preview
SPF-1010-TY
Brand: TUYA Pages: 18
on2 PETS 5 FT. INTERCHANGEABLE LEAF BRANCHES CAT TREE Quick Start Manual preview
5 FT. INTERCHANGEABLE LEAF BRANCHES CAT TREE
Brand: on2 PETS Pages: 4
INVISIBLE FENCE Invisible Gate Plus Owner'S Manual preview
Invisible Gate Plus
Brand: INVISIBLE FENCE Pages: 16
sanowell 4867380 Instruction Manual preview
4867380
Brand: sanowell Pages: 56
Petsafe Drinkwell PWW00-13705 Operating Manual preview
Drinkwell PWW00-13705
Brand: Petsafe Pages: 16
Ferplast ATLAS 40 PROFESSIONAL Assembly Instructions preview
ATLAS 40 PROFESSIONAL
Brand: Ferplast Pages: 2
Ferplast 50 CLASSIC Assembly Instructions preview
50 CLASSIC
Brand: Ferplast Pages: 4
Taurus 955101 Instructions For Use Manual preview
955101
Brand: Taurus Pages: 60
E-Collar Technologies Pro Educator PE-900 Quick Start Manual preview
Pro Educator PE-900
Brand: E-Collar Technologies Pages: 11
Dynavet Effitek Instructions For Use preview
Effitek
Brand: Dynavet Pages: 5
Wahl CLIP'N'RINSE Instruction Manual preview
CLIP'N'RINSE
Brand: Wahl Pages: 12
AccuRelief ACRL-2000 User Manual preview
ACRL-2000
Brand: AccuRelief Pages: 44

Brands by name

Popular brands

Load more brands